Related Manuals for Oneida Air Systems 5 & 7.5 HP Direct Drive Cyclonic Dust Collectors
Summary of Contents for Oneida Air Systems 5 & 7.5 HP Direct Drive Cyclonic Dust Collectors
- Page 1 5 & 7.5 HP Direct Drive Cyclonic Dust Collectors Owner’s Manual Oneida Air Systems, Inc. 1001 West Fayette St., Syracuse, N.Y. 13204 Phone 1-800-732-4065 315-476-5151 Fax 315-476-5044 www.oneida-air.com...
-
Page 2: Table Of Contents
Thank You for Choosing an Oneida Air Systems Product! OAS manufactures and sells dust collection equipment only. Our qualified technicians and sales staff are available 7:30am - 6:00pm EST Mon. - Thur. and 7:30am - 5:00pm EST Fri. to answer any questions concerning OAS products and dust collection. Call for ductwork design and ductwork quotes, including system pricing and shipping cost. -
Page 3: System Start-Up Information
2. Install Ductwork completely: A.) Seal ductwork with silicone sealant or duct tape. B.) Have Dust Bin in place and sealed before running Dust Collector. 3. Wire Fan / Blower according to wire diagram on pg. 11 in this owner’s manual. -
Page 4: Direct Drive Configurations
1. No Filter - Vent Outside - Caution: If exhaust air is vented outside you must provide make up / return air. Flue gases (carbon monoxide) can be drawn into the shop from furnaces, water heaters or other appliances. Plenum Assembly Pleated Cartridge Filters... -
Page 5: General Specifications & Fan Performance Curve
Physical and Electrical Data for 5 and 7.5hp Direct Drive Systems. System Performance 5hp 1220 max cfm - 2250 cfm w/ typical ductwork 7.5hp 2900 max cfm - 2500 cfm w/ typical ductwork System Dimensions Height w/ 55 Gal. Drum: 132” Footprint: 8.5’... -
Page 6: Dimensions
IV. Dimensions Top View Bolt Holes 30 3/8” 102” 24 1/4” 36” 1.25” Flange 7.64” I.D. 10.031” I.D. 5 - 7.5 HP Direct Drive Owner’s Manual 1.5” 32 1/8” O.D. of Mounting Ring 122.125” w/ 55 gal. steel drum 69.875” Note: Overall height dimensions are w/ 55 gal. - Page 7 V. Angle Iron Stand 1. Choose the system orientation, plenum can be on the right or the left of the cyclone. Bolt together the stand using the cross bars and 3/8” x 1” bolts. Note: the cross bar on the cyclone stand goes in the back so that the dust bin can slide out. Cross Brace for Cyclone Angle Ring to sit on...
- Page 8 Fan / Blower is shipped strapped to Cyclone Barrel. It is NOT attached to the unit. You must bolt them together. Follow the instructions below. 1. Orient the blower housing to match the stand configuration and the desired angle for the cyclone inlet. Bolt the fan / blower to the cyclone barrel using the hardware taped on the motor.
-
Page 9: Fan / Blower Maintenance
5. Attach flex hose to bottom of collector and to lid of dust bin. Securely fasten hose clamps. There must be an air tight seal between the collector and dust bin. 6. Make sure the dust bin lid sits securely and the rubber gasket on the bin lid is in place on the barrel. -
Page 10: External Filter Box Assembly
Build your own plenum Plenum box can be constructed of plywood or metal. Oneida Air Systems sells 22 gauge galv. plenum boxes. The filter medium is a 16 ounce polyester felt which has been singed inside to help release caked dust. -
Page 11: Filter Maintenance
External Filter Cartridge Cleaning Intervals When unit is turned off, use compressed air to blow dust off from exterior of filter. Hold nozzle at least 8” away from filter pleats*. Do not remove bottom dust pan before or during the blow-off process! Let dust settle into dust pan. - Page 12 Use wiring diagram on motor plate if different from below. Wiring should always be done by a licensed electrician! - Electrically insulate all connections. - For counter-clockwise rotation, looking from top of motor down. 5hp Single Phase Leeson Motor / 230v / 19.8 amps / TEFC / C Face / 3500 rpm Power Line 1* Tie together and insulate with a wire nut (do NOT connect to...
-
Page 13: Accessories
Bindicator - Provides level sensing for dry bulk solids. The Bindicator operates by using a 1 rpm synchronous motor to rotate a paddle. When paddle rotation is impeded by material surrounding it, the motor is de-energized and triggers a SPDT snap switch. The snap switch can be used in conjunction with a motor starter to turn equipment off or provide alarm functions. -
Page 14: Troubleshooting
Air leaks between the collector and dust bin - The lid of the dust bin and the cyclone must be in place and sealed when operating the dust collector. - Make sure flex hose is not torn and the hose clamps are tight. -
Page 15: Fire Hazards
A good dust collection system reduces overall fire hazards but also adds new concerns. A fire hazard is still present. Combustible material is now in the dust collector and storage container. The following points are worth heeding: It is the buyer’s responsibility to follow all applicable federal, state, local, OSHA, NFPA, or authorities having... -
Page 16: Terms And Conditions
Oneida Air Systems shall be tried in the State of New York, County of Onondaga. Oneida Air Systems shall in no event be liable for death, injuries to persons or property or for incidental, contingent, special, or consequential damages arising from the use of our product.