Daikin DCM601A51 User Manual page 323

Large History
Middle classification
classification type
B. Monitoring/ Error Error
Operation (including External/
Error
BACnet)
Error
Error
Error
Error
Error
Error
Error
Release B012
Error
Error
Error
Error
Release B018
Error
Error
Release B021
Release B022
Error
Release B024
Error
Error
Release B027
BACnet-related Error Error
Release B032
Status Change Status
Status
Status
Status
Status
Status
Status
Status
Status
Status
Status
Status
Status
Status
Status
Status
Status
Status
Status
Status
Status
Status
Message*1
History
Record No.
Content
B001 Instrument Combination Err
B002 Address Duplicated
B003 D3 port master duplication error
B004 D3 Plus Adptr Comm Err
B005 Instr Comm Err
B006 D3 port autoconfig. error
B007 D3 port transmission buffer overflow
B010 A/C error Detection (Unit[Unit No.])
B011 A/C error detected (Unit[Unit No.])
A/C error Restoration
B013 A/C error Detection
B014 A/C error detected
B016 Equipment error Detection
B017 Equipment error detected
Equipment error Restoration
B019 Analog upper limit error detected
B020 Analog lower limit error detected
Analog upper limit error Restoration
Analog lower limit error Restoration
B023 Communication error detected
Communication restored
B025 Equipment error Detection
B026 Equipment error detected
Equipment error Restoration
B031 Communication error detected*3
Communication restored
B101 [Start/Stop/Setback High/Setback Low]
B102 Operation mode changed ([Operation Mode])
B103 Setpoint changed ([Setpoint]°F)
B104 Fan speed changed ([Fan])
B105 Airflow Direction ([Airflow Direction])
B106 Rmt Ctlr setup
([Rmt Ctlr enabled/Rmt Ctlr disabled/Rmt Ctlr enable stop] Mode enabled/Mode disabled]
[Temp. enabled/Temp. disabled])
B107 Filter Sign Reset
B108 [Start/End] Timer Extension
B109 Cool set temp limit [enabled/disabled] ([Cool Set Temp Limit Range])
B110 Heat set temp limit [enabled/disabled] ([Heat Set Temp Limit Range])
B112 Ventilation mode changed ([Ventilation Mode])
B113 Ventilation amount changed ([Ventilation Amount])
B114 Repeat Mode [enabled/disabled] ([Interval] min)
B115 Modify [Analog Value] [°C/°F]
B116 Modify [MultiState value]
B130 Reheat start/Reheat stop
B131 Leaving Water setpoint(Cool) changed (°C/°F)
B132 Leaving Water setpoint(Heat) changed (°C/°F)
B133 Storage Water setpoint changed (°C/°F)
B134 Leaving Water setpoint changed (°C/°F)
B135 Low noise On/Low noise Off
B136 Storage start/Storagestop
User's Manual EM11A015B
intelligent Touch Manager
Name Instructed by*2
DIII-NET
DIII-NET
DIII-NET
DIII-NET
DIII-NET
DIII-NET
DIII-NET
[Management Point Name]
[Management Point Name]
[Management Point Name]
[Management Point Name]
[Management Point Name]
[Management Point Name]
[Management Point Name]
[Management Point Name]
[Management Point Name]
[Management Point Name]
[Management Point Name]
[Management Point Name]
[Management Point Name]
[Management Point Name]
[Management Point Name]
[Management Point Name]
[Management Point Name]
[Management Point Name]
[Management Point Name]
[Management Point Name] [Status Source]*4
[Management Point Name] [Status Source]
[Management Point Name] [Status Source]
[Management Point Name]
[Management Point Name]
[Management Point Name]
[Management Point Name]
[Management Point Name]
[Management Point Name]
[Management Point Name]
[Management Point Name]
[Management Point Name]
[Management Point Name]
[Management Point Name]
[Management Point Name]
[Management Point Name] [Status Source]
[Management Point Name] [Status Source]
[Management Point Name] [Status Source]
[Management Point Name] [Status Source]
[Management Point Name] [Status Source]
[Management Point Name] [Status Source]
[Management Point Name]
322