Omntec OEL8000II Installation Manual page 11

SECTION 5
5.1 L
5.2 S
5.3 O
5.4 R
5.5 R
5.6 T
Installation Manual
4.3.4.11 Low/Low Product Alarm Point............................................................................. 4-21
4.3.4.12 Delivery Needed Alarm Point............................................................................... 4-22
4.3.4.13 Low Product Point ................................................................................................ 4-22
4.3.4.14 High Product Point ............................................................................................... 4-22
4.3.4.15 High Product Warning Point................................................................................. 4-23
4.3.4.16 Overfill Product Alarm Point................................................................................ 4-23
4.3.4.17 High/High Product Alarm Point ........................................................................... 4-23
4.3.4.18 Tank Diameter ...................................................................................................... 4-23
4.3.4.19 Probe Length......................................................................................................... 4-24
4.3.4.20 Tank Capacity....................................................................................................... 4-24
4.3.4.21 Volume Offset ...................................................................................................... 4-24
4.3.4.22 Automated VLD (Volume Leak Detection Test) .................................................. 4-25
4.3.4.23 Sudden Loss Limit................................................................................................ 4-27
4.3.4.24 Table Size ............................................................................................................. 4-27
4.3.5 Sensor Data .................................................................................................... 4-28
4.3.5.1 Config (Sensor) Submenu..................................................................................... 4-30
4.3.5.1.1 Sensor Labeling ............................................................................................ 4-31
4.3.5.1.2 Other Label................................................................................................... 4-34
4.3.5.1.3 Editing Sensor Labels ................................................................................... 4-35
4.3.5.1.4 Temperature Sensor Programming............................................................... 4-37
4.3.5.1.5 Vapor Sensor Programming ......................................................................... 4-38
4.3.5.2 Test/Del (Sensor) Submenu .................................................................................. 4-41
4.3.5.2.1 Testing and Deleting Sensors........................................................................ 4-41
4.3.5.2.2 Setting Sensor Priority.................................................................................. 4-43
4.3.6 Clearing Logs (Alarm, Drop, CITLD, and VLD) ........................................... 4-45
4.3.7 Shift Data........................................................................................................ 4-46
4.3.8 Remote Data ................................................................................................... 4-48
4.3.8.1 Site Alarm Acknowledge Time ............................................................................ 4-49
4.3.8.2 Remote Horn Timeout .......................................................................................... 4-49
4.3.8.3 Remote Horn Time Enable/Disable ...................................................................... 4-50
4.3.9 Comm ............................................................................................................. 4-51
4.3.9.1 Serial..................................................................................................................... 4-51
4.3.9.1.1 COM1 ........................................................................................................... 4-52
4.3.9.1.2 COM2 ........................................................................................................... 4-53
4.3.9.1.3 COM3 ........................................................................................................... 4-56
4.3.9.2 Modem.................................................................................................................. 4-57
4.3.9.2.1 Autofax and Datamodem............................................................................... 4-58
4.3.9.2.2 Ip Modem...................................................................................................... 4-60
4.3.9.3 RS485 ................................................................................................................... 4-60
4.3.10 Int Brd ............................................................................................................ 4-61
4.3.10.1 Programming the IB-RB2 Relay Board ................................................................ 4-62
4.3.10.1.1 Tank Activation............................................................................................. 4-64
4.3.10.1.2 Sensor Activation (non-product distinguishing)............................................ 4-65
4.3.10.1.3 Sensor Activation (product distinguishing)................................................... 4-65
4.3.10.1.4 Temperature (BX-TC) Sensor Activation ...................................................... 4-66
4.3.10.2 Programming the IB-C420 Board ......................................................................... 4-67
4.3.10.3 Programming the IB-12V Low Voltage Board ..................................................... 4-68
4.3.10.4 Programming the IB-NET Board.......................................................................... 4-68
4.3.11 Report ............................................................................................................. 4-68
4.3.12 Units ............................................................................................................... 4-69
4.3.13 Language........................................................................................................ 4-70
PROCEDURES ....................................................................................... 5-1
T ........................................................................................................ 5-1
OOPBACK EST
P
ETTING RODUCT AND
D VLD T
N EMAND ESTING
T RAS A
EMOTE ESTING OF
C
EPLACING ONTROLLER
S
ROUBLESHOOTING ENSORS
5.6.1 Condition #1 ..................................................................................................... 5-2
W H (C
ATER EIGHT ALIBRATION
...................................................................................... 5-1
................................................................ 5-1
NNUNCIATOR
B ....................................................................... 5-1
ATTERIES
.................................................................................... 5-2
OEL8000II
) ......................................... 5-1
xi