Power Jumper Contacts/Field Supply; Figure 3: Power Jumper Contacts; Table 4: Legend For Figure "Power Jumper Contacts - WAGO 750-439/040-000 Manual

18 Device Description
Pos: 18.11 /Serie 750 (WAGO-I/O-SYSTEM)/Gerätebeschreibung (alte Struktur)/Anschlüsse/Leistungskontakte/Feldversorgung - Überschrift 3 @ 6\mod_1256294692864_21.docx @ 43664 @ 3 @ 1
3.2.2

Power Jumper Contacts/Field Supply

Pos: 18.12.1 /Serie 750 (WAGO-I/O-SYSTEM)/Wichtige Erläuterungen (alte Struktur)/Sicherheits- und sonstige Hinweise/Vorsicht/Vorsicht: Verletzungsgefahr durch scharfkantige Messerkontakte! @ 6\mod_1256193279401_21.docx @ 43414 @ @ 1
Risk of injury due to sharp-edged blade contacts!
The blade contacts are sharp-edged. Handle the I/O module carefully to prevent
injury. Do not touch the blade contacts.
Pos: 18.12.2 /Serie 750 (WAGO-I/O-SYSTEM)/Gerätebeschreibung (alte Struktur)/Anschlüsse/Leistungskontakte 2 LK (Messer/Feder) - Einleitung @ 15\mod_1371721641099_21.docx @ 123714 @ @ 1
The I/O module 750-439/040-000 has 2 self-cleaning power jumper contacts that
supply and transmit power for the field side. The contacts on the left side of the
I/O module are designed as blade contacts and those on the right side as spring
contacts.
Pos: 18.12.3 /Serie 750 (WAGO-I/O-SYSTEM)/Gerätebeschreibung (alte Struktur)/Anschlüsse/Leistungskontakte 2 LK (Messer/Feder) - Abbildung, doppelte Breite, Ex i @ 30\mod_1508428592212_21.docx @ 467258 @ @ 1

Figure 3: Power Jumper Contacts

Pos: 18.12.4 /Serie 750 (WAGO-I/O-SYSTEM)/Gerätebeschreibung (alte Struktur)/Anschlüsse/Leistungskontakte 2 LK (Messer/Feder) - Legende @ 15\mod_1371721352500_21.docx @ 123710 @ @ 1

Table 4: Legend for Figure "Power Jumper Contacts"

Contact
1
2
3
4
Pos: 18.12.5 /Serie 750 (WAGO-I/O-SYSTEM)/Wichtige Erläuterungen (alte Struktur)/Sicherheits- und sonstige Hinweise/Achtung/Achtung: Maximaler Strom Ex i Einspeisung 750-0606/040-000 XTR @ 28\mod_1486128985806_21.docx @ 405244 @ @ 1
Do not exceed maximum current via power contacts!
The maximum current available from the "Power Supply 24 VDC Diagn for Ex i
XTR Modules" 750-606/040-000 is 1 A.
When configuring the system, ensure that this current is not exceeded.
If exceeded, an additional 750-606/040-000 must be used.
Pos: 18.13 /Dokumentation allgemein/Gliederungselemente/---Seitenwechsel--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1
Manual
Version 1.1.0
Type Function
Spring contact Potential transmission (U
Spring contact Potential transmission (0 V) for field supply
Blade contact Potential feed-in (0 V) for field supply
Blade contact Potential feed-in (U
WAGO I/O SYSTEM 750 XTR
750-439/040-000 8DI NAMUR Ex i XTR
) for field supply
v
) for field supply
v