Champion DH6000 Operation, Cleaning, And Maintenance Manual page 9

Shipping weight crated: 300 lbs.
5-3/4"
[145]
Min
Clearance
7-1/4"
[184]
4-11/16"
5-3/4"
5-3/4"
[146]
[146]
Inside Table
UTILITIES
1 Electrical Machine Connection
(See Electrical Box)
2 Hot Water 3/4" NPT Hot Water 110° - 140°F
20-22 PSI Flow Pressure
3 Drain 1.5" OD Connection; 15 GPM Max
Flow (Drain water tempering height 5")
4 Drain Water Tempering 1/2" Cold water
line with customer supplied cut-off valve
(optional)
5 Integrated Detergent System Detergent
bottle supply connections (optional)
68"
64-5/16"
[1727]
[1634]
Warning: Plumbing, electrical connections should be
48-7/8" made by qualified personnel who will observe all the
72"
[1242]
applicable plumbing, sanitary and safety codes and the
66-1/16"
National Electrical Code.
[1678]
3-9/16"
Note: Optional Drain Tempering: 1/2" NPT cold water [91]
connection required. 1/2" NPT drain connection from back flow
11-5/16"
preventer to house drain. (FIELD INSTALLED and PLUMBED). [288]
3-9/16"
Due to an ongoing value analysis program at
[91]
Champion, specifications contained in this catalog
are subject to change without notice.
11-5/16"
[288]
Champion Industries, Inc.,
3765 Champion Blvd., NC 27105
19-1/2"
336/661-1556 • Fax: 336/661-1979
ChampionIndustries.com
17-3/16"
[437]
72"
[1829]
4-3/8"
[110]
50-7/8"
[1293]
31-5/8"
[804]
Side View
[119]
18-7/16"
18-7/16"
[469] [469]
6-7/8"
6-7/8"
[175]
[175]
4-13/16"
4-13/16"
[122]
25-3/8"
[122] 6-1/16"
[645] [154]
6-1/16"
25-3/8"
Inside Table
[154]
[645]
Flange
Flange
26-7/8"
Plan View
[683]
26-7/8"
[683]
34-1/8"
[866]
34"
[863]
33-5/8"
[853]
8-9/16"
[217]
6-1/4"
[159]
33-5/8"
[853]
19-1/2"
8-9/16"
[496]
[217]
4-7/16"
[112]
6-1/4"
[159]
[496] Note: Water Hammer Arrestor (meeting ASSE-1010 standard or equivalent)
4-7/16"
to be supplied (by others) in common water supply line at service connection.
[112]
25-3/8"
[645]
Inside Table
Flange
26-7/8"
[683]
34"
[863]
66-1/16"
[1678]
3-9/16"
[91]
11-5/16"
[288]
19-1/2"
Front View [496]
Corner Table
Configuration
Machine & Built-in Booster (Standard)
Rated Minimum Supply
Voltage Amps Circuit Ampacity
Rinse
208-240/60/1 77-68 100
Pressure
Rinse Aid
208-240/60/3 46-41 60
Gauge
Rinse Injection
Pressure
480/60/3 20 30 1/8" NPT
Gauge
Machine Only
(two point electrical connection or no built-in booster)
Minimum
Rated Supply Circuit
Voltage Amps Ampacity
208-240/60/1 38-34 50
208-240/60/3 25-23 30
480/60/3 11 15
Booster Only (two point electrical connection)
8-5/16"
Minimum
[212]
Rated Supply Circuit
Voltage Amps Ampacity
208-240/60/1 39-34 50
208-240/60/3 21-18 25
480/60/3 9 15
an Ali Group Company
6-7/8"
[175]
4-13/16"
[122]
6-1/16"
[154]
Hood-type Dishwashing Machine
33-5/8"
[853]
8-9/16"
[217]
6-1/4"
[159]
4-7/16"
[112]
6" [152]
to Inside
Tank Wall
8-1/8" [207]
to Rack
Guide
SPECIFICATIONS
Maximum
Overcurrent Capacities
Protective Device
100
60 Motor horsepower
Water consumption
30
Rinse Aid
Injection
1/8" NPT
Temperature °F
Maximum
Overcurrent
Protective Device
Detergent
Heating
50
Injection
7/8" Dia
30
Detergent
Injection
Detergent
15
Probe
7/8" Dia
7/8" Dia
Selectable cycle
Maximum
Overcurrent
times in minutes
Protective Device
Detergent
50
Probe
Wash
7/8" Dia
25
Rinse
15
Sanitary Dwell
Total
Specification Sheet
DH6000
High Temperature
Dimensions shown in inches and [mm]
Rinse
Pressure
Rinse Aid
Gauge
Injection
1/8" NPT
Detergent
Injection
7/8" Dia
Detergent
Probe
7/8" Dia
Side View
30"
[762]
7-1/4" [184]
1-1/2" [32] Roll
21-3/8"
[543]
1-1/8"
[29]
Typical Table Construction
Racks per hr. (NSF rated)
Wash tank (gal.)
Gal. per hr. (max. use)
Gal. per rack
Wash
Rinse
Tank heat, electric 5.2 kW
Electric Booster 7.5 kW
Dish- Pot &
washer Pan
Mode Mode
1 2 4
Time cycles in seconds
36 94 214
8 10 10
16 16 16
60 120 240 360
60
10
2 HP
39
0.73
150
180
6
334
10
16
v