Table of Contents
Advertisement
CMOS Clear (JBT1)
JBT1 is used to clear the saved system setup configuration stored in the CMOS
chip. To clear the contents of the CMOS, completely shut down the system, remove
the AC power cord and then short JBT1 with a jumper. Remove the jumper before
powering on the system again. This will erase all user settings and revert everything
to their factory-set defaults.
PCI Slot SMB Enable (I
Use Jumpers I
C1/I
2
SMB (System Management Bus) support
to improve system management for the
PCI slots. See the table on the right for
jumper settings.
C
PCIE1
JPCIE2
JI2C1/JI2C2
ON:ENABLE
OFF:DISABLE
JI2C2
JI2C1
1
2
B
J_1394
1
5
2
JTPM1
JPME1:
1-2:NORMAL
2-3:ME RECOVERY
JWD1:
WATCH DOG
1-2:RST
2-3:NMI
JWOR1:
19
WAKE ON RING
JWD1
20
3
JPME1
3
1
1
A
JSTBY1
3
1
USB4/5
7
10
2
1
USB 2/3
USB6/7
USB 2/3(3.0)
7
10
JLED1
JLED1:
1
3 PIN POWER LED
T-SGPIO2
1
I-SATA0
T-SGPIO1
I-SATA1
1
JF1
LED1
C1/I
C2)
2
2
C2 to enable PCI
2
JPAC1
1
1
1
JSPDIF_OUT
FAN5
JPAC1:AUDIO
1-2:ENABLE
2-3:DISABLE
PCIE3
JPCIE4
PCIE5
JPCIE6
JPL2
LAN2
1-2
ENABLE
2-3
DISABLE
JPL1
1-2
2-3
JBT1
BATTERY
JPME2
1
JBR1
USB12/13
1
JBR1:
1-2:NORMAL
2-3:BIOS RECOVERY
1
19
USB 0/1(3.0)
JSD1
JD1
1
4
I-SATA2
I-SATA4
A-SATA0
1
4
I-SATA5
I-SATA3
A-SATA1
FAN3
2-33
PCI Slot_SMB Enable
Jumper Setting
Short
Open (Default)
A. Clear CMOS
B. JI
2
C. JI
2
CLEAR CMOS SWITCH
HD AUDIO
USB 16/17
USB 14/15
USB 6/7(3.0)
USB 4/5(3.0)
1
LAN2
LAN1
JPL2
1
LAN1
ENABLE
DISABLE
CPU
BIOS LICENSE
Tested to Comply
With FCC Standards
FOR HOME OR OFFICE USE
ALWAYS POPULATE BLUE SOCKET FIRST
UNB NON-ECC DDR3 DIMM REQUIRED
R298
10
SP1
11
JPW1
1
JF1
JD1:
PWR
X
OH/FF
SPEAKER:1-4
13
24
RST
ON
BUZZER:3-4
LED
Chapter 2: Installation
Jumper Settings
Definition
Enabled
Disabled
C1
C2
THUNDERBOLT
HDMI
VGA/DVI
USB 0/1
1
1
JVR1
3
2
1
P1-DIMMA1
P1-DIMMA2
P1-DIMMB1
P1-DIMMB2
1
3
4
1
HDD PWR
NIC2
NIC1
LED
LED
1
4
1
4
Advertisement
Table of Contents
