Mitsubishi Electric FDF100VSXVD Technical Manual page 204

6. Function setting
Each function of the remote controller and the indoor unit is automatically set to the initial setting, which is the standard use, on the occasion of connecting the remote controller with the indoor unit. In the case of the standard
use, the setting change is unnecessary. However, if you whould like to change the initial setting " ○ ", change the setting for only the item of the function number. Record the setting contents and stored them.
⑴
Function setting item by switch on PCB
Switch No. Setting Setting detail
ON Slave remote controller
SW1-1
OFF Master remote controller
ON Remote controller thermistor enabled
SW1-2
OFF Remote controller thermistor disabled
ON "MODE" button prohibited
SW1-3
OFF "MODE" button enabled
ON "ON/OFF" button prohibited
SW1-4
OFF "ON/OFF" button enabled
⑵
Function setting item by button operation
Classification Function No. Function
01 Indoor unit fan speed
Remote controller
03 thermistor at the time
of cooling
Remote
controller
function
Remote controller
04 thermistor at the time
of heating
05 Ventilation setting
"Auto" operation
06
setting
Operation permission/
07
prohibition
08 External input
09 Fan speed setting
Fan remaining
10 operation at the time
of cooling
Fan remaining
11 operation at the time
of heating
Indoor unit
function
Setting temperature
12 offset at the time of
heating
13 Heating fan controller
Return air temperature
14
offset
Note 1: The symbol " ※ " in the initial setting varies depending upon the indoor unit and the outdoor unit to be connected, and this is
automatically determined as follows:
Swith No.
Function
Function No.
"FAN SPEED" button prohibited Product model whose indoor fan speed is only one step
"FAN SPEED"
SW1-6
button "FAN SPEED" button enabled
Fan speed: three steps
Indoor unit fan
Fan speed: two steps (Hi-Lo) Product model whose indoor unit fan speed is two steps
Remote controller function 01
Fan speed: two steps (Hi-Me)
speed
Fan: one step
"Auto" operation "Auto" operation enabled
Remote controller function 06
setting "Auto" operation disabled
Heating fan Low fan speed
Indoor unit function 13
control
Intermittent operation
Initial setting Switch No.
SW1-5
○
SW1-6
○
SW1-7
○
SW1-8, 9, 0
○
Setting No. Setting
01 Fan speed: three steps
02 Fan speed: two steps (Hi-Lo)
03 Fan speed: two steps (Hi-Me)
04 Fan: one step
01 Remote controller thermistor: no offset
02 Remote controller thermistor: +3.0 °C
03 Remote controller thermistor: +2.0 °C
04 Remote controller thermistor: +1.0 °C
05 Remote controller thermistor: -1.0 °C
06 Remote controller thermistor: -2.0 °C
07 Remote controller thermistor: -3.0 °C
01 Remote controller thermistor: no offset
02 Remote controller thermistor: +3.0 °C
03 Remote controller thermistor: +2.0 °C
04 Remote controller thermistor: +1.0 °C
05 Remote controller thermistor: -1.0 °C
06 Remote controller thermistor: -2.0 °C
07 Remote controller thermistor: -3.0 °C
01 No ventilator connection
02 Ventilator links air-conditioner
01 "Auto" operation enabled
02 "Auto" operation disabled
01 Disabled
02 Enabled
01 Level input
02 Pulse input
01 Standard
02 High speed 1
03 High speed 2
01 No remaining operation
02 0.5 hours
03 1 hour
04 6 hours
01 No remaining operation
02 0.5 hours
03 2 hours
04 6 hours
01 No offset
02 Setting temperature offset + 3.0 °C
03 Setting temperature offset + 2.0 °C
04 Setting temperature offset + 1.0 °C
01 Low fan speed
02 Setting fan speed
03 Intermittent operation
04 Fan off
01 No offset
02 Return air temperature offset +2.0 °C
03 Return air temperature offset +1.5 °C
04 Return air temperature offset +1.0 °C
05 Return air temperature offset -1.0 °C
06 Return air temperature offset -1.5 °C
07 Return air temperature offset -2.0 °C
Setting Product model
Product model whose indoor fan speed is two steps or three
steps
Product model whose indoor unit fan speed is three steps
Product model whose indoor unit fan speed is only one step
Product model where "Auto" mode is selectable
Product model without "Auto" mode
Product model except FDUS
FDUS
Setting Setting detail
ON "TEMP" button prohibited
OFF "TEMP" button enabled
ON "FAN SPEED" button prohibited
OFF "FAN SPEED" button enabled
ON Auto restart function enabled
OFF Auto restart function disabled
ON
Not used
OFF
Initial setting
-
※ Note 1 The fan speed is three steps,
-
※ Note 1 The fan speed is two steps,
-
The fan speed is two steps,
※ Note 1 The fan speed is fixed to one step.
○
At the time of cooling, in the case of remote controller thermistor enabled, offset temperature at +3.0°C.
At the time of cooling, in the case of remote controller thermistor enabled, offset temperature at +2.0°C.
At the time of cooling, in the case of remote controller thermistor enabled, offset temperature at +1.0°C.
At the time of cooling, in the case of remote controller thermistor enabled, offset temperature at -1.0°C.
At the time of cooling, in the case of remote controller thermistor enabled, offset temperature at -2.0°C.
At the time of cooling, in the case of remote controller thermistor enabled, offsett temperature at -3.0°C.
○
At the time of heating, in the case of remote controller thermistor enabled, offset temperature at +3.0°C.
At the time of heating, in the case of remote controller thermistor enabled, offset temperature at +2.0°C.
At the time of heating, in the case of remote controller thermistor enabled, offset temperature at +1.0°C.
At the time of heating, in the case of remote controller thermistor enabled, offset temperature at -1.0°C.
At the time of heating, in the case of remote controller thermistor enabled, offset temperature at -2.0°C.
At the time of heating, in the case of remote controller thermistor enabled, offset temperature at -3.0°C.
○
In case of Single split series, by connecting ventilation device to CNT of the indoor printed circuit board (in case of VRF series, by
connecting it to CND of the indoor printed circuit board), the operation of ventilation device is linked with the operation of indoor unit.
※ Note 1
※ Note 1 "Auto" operation disabled
○
Operation permission/prohibition controller is enabled.
○
Note2
Note2
Note2
○ After cooling stopped, no fan remaining operation
After cooling stopped, fan remaining operation for 0.5 hours
After cooling stopped, fan remaining operation for 1 hour
After cooling stopped, fan remaining operation for 6 hours
○
After heating stopped or after heating thermostat OFF, no fan remaining operation
After heating stopped or after heating thermostat OFF, fan remaining operation for 0.5 hours
After heating stopped or after heating thermostat OFF, fan remaining operation for 2 hours
After heating stopped or after heating thermostat OFF, fan remaining operation for 6 hours
○
The setting temperature at the time of heating is offset by +3.0 °C.
The setting temperature at the time of heating is offset by +2.0 °C.
The setting temperature at the time of heating is offset by +1.0 °C.
※ Note 1 At the time of heating thermostat OFF, operate with low fan speed.
At the time of heating thermostat OFF, operate with the setting fan speed.
※ Note 1 At the time of heatingr thermostat OFF, intermittently operate.
At the time of heating thermostat OFF, a fan will be stopped.
When the remote controller thermistor is enabled, automatically set to "Fan off". Do not set at the time of the indoor unit thermistor.
○
Offset the return air temperature of the indoor unit by +2.0 °C.
Offset the return air temperature of the indoor unit by +1.5 °C.
Offset the return air temperature of the indoor unit by +1.0 °C.
Offset the return air temperature of the indoor unit by -1.0 °C.
Offset the return air temperature of the indoor unit by -1.5 °C.
Offset the return air temperature of the indoor unit by -2.0 °C.
Note 2: Fan speed of "High speed" setting
Fan speed setting
Standard
High speed 1・2
Initial setting of some indoor unit is "High speed".
Note 3: As for plural indoor unit, set indoor functions to each master and slave indoor unit.
But only master indoor unit is received the setting change of indoor unit function "07 Operation permission/
prohibition" and "08 External input".
- 203 -
'11 • PAC-T-160
SW1
ON
Initial setting
OFF
1 2 3 4 5 6 7 8 9 0
○
※ Note 1
※ Note 1
• As for the slave remote controller, function setting is impossible
○
other than SW1-1.
•
In the indoor unit with only one fan speed, "FAN SPEED" button cannot
be enabled.
Remarks
-
.
.
.
Indoor unit fan speed setting
- - -
Hi − Mid − Lo Hi − Lo
UHi − Hi − Mid UHi − Mid
-
Hi − Mid
UHi − Hi