CARE MODE - HOW TO USE WARM BATH FUNCTION
貼 心 模 式 - 溫 暖沐浴 功 能 的 使用方法
1.
Hot startup function: After the product starts up in the heating mode when the temperature
in the bathroom is lower than 20 °C, it enters the hot startup status to avoid blowing of cold
air, and the fan runs at a low speed. When the temperature in the bathroom reaches 20 °C or
above or after running for 60 seconds, the hot startup status stops and the fan runs at a high
speed.
熱啟動功能:當浴室溫度低於20 °C時, 以 暖氣 模式 啟動後,為避免冷風吹出,產品進入熱啟動狀態,
扇葉以低速運轉,待浴室溫度達至20 °C以 上或 經過60秒後,熱啟動狀態停止,扇葉以高速運轉。
2.
Heater may stop heating when temperature in bathroom is up to required degree,
and may restart heating as the temperature in bathroom cools down.
當浴室內 溫 度 上 升 到 一 定程 度時 ,加 熱器 停 止工 作, 待溫度下降到一定程度後,加熱器重新開始
工作 。
Use when you feel cold in a bath
Before taking a bath, start the heating function to warm the bathroom
beforehand.
在沐浴前開暖氣功能,可提前把浴室加溫。
1
Press the
button to start the heating mode at the HI. It will switch
to the VENT. mode at the HI. automatically when the set time is up.
After 3 minutes ,it will switch to the VENT. mode at the LO.
automatically and run continuously.
按
按鈕 ,溫 暖沐 浴模 式以暖氣強檔開始運轉。運轉至所設時間後自動進入
換氣 強檔 模式 ,運 轉三 分鐘 後自動進入換氣弱檔模式並連續運轉。
HEAT(HI.)
(Initial settings)
暖氣強檔
(初始 設置)
(15 minutes)
During running, you can press
2
enter the ventilation state, the time is not adjustable.)
運轉 過 程中 ,可 通過
(暖 氣結 束後 ,進 入換 氣狀 態,時間不可調。)
3
During operation, you can press the
direction.(After heating , enter the ventilation state and the wind
direction is not adjustable.)
運轉 過 程中 ,可 通過
(暖 氣結 束後 ,進 入換 氣狀態,風向不可調。)
4
During operation, you can press the
(After heating , enter the ventilation state and the air type is not
adjustable.)
運轉 過 程中 ,可 通過
(暖 氣結 束後 ,進 入換 氣狀態,風種不可調。)
5
To stop midway in running,pressthe button.
如需在運轉途中停止,請按
In the heating mode running for 30 seconds above, press the
button to stop the heater. The fan will stop running after a delay
of 20 seconds.
若在 暖氣 模式 運轉30秒 以上,按
扇 葉將 延 遲20秒 停止 運轉 。
在浴室中感到冷時使用
VENT.(HI.)
換氣強檔
(3 minutes)
( 15分鐘)
(3分 鐘)
The remote does not
display this status time
遙 控 器不顯示此 狀 態 時 間
to change the set time.(After heating ,
調 整設置時間。
按 鈕,調整風向。
按 鈕,調整風種。
按鈕。
按鈕後,為使加熱器冷卻,
VENT.(LO.)
換氣弱檔
(continued)
(持 續)
button to change the air
button to change the air type.
23