Check=Print; Test Print Menu; Printer Status Menu; Printing A Status Check - Epson Stylus Pro 10000 Product Information

Error conditions (continued)
Display
Message/Light Explanation
/ Paper could not be
RELOAD PAPER
light reversed into the
Paper Out
on printing position.
Image is too wide for
the paper loaded in the
printer.
Paper is not fully
ejected.
PAPER NOT CUT
was cleared.
/ Paper is too thick for
REMOVE PAPER
Paper Out light print head cleaning.
on
SERVICE REQ. An error has occured.
/
<error number>
All lights flashing
The waste ink system is
SERVICE REQ.
00000100/ full.
All lights flashing
TURN PWR OFF This message appears
AND ON
after you clear a paper
jam.
UNABLE TO You tried to print a test
PRINT
pattern while an error
condition was present or
the ink compartment
cover was open.
Wrong ink cartridge
WRONG
CARTRIDGE / Ink installed.
Out light(s) on
Response
Remove the paper.
Reload it so that the
right and bottom edges
are straight and aligned
with both rows of holes.
Resize your image or
load wider paper.
Cut the paper at the
paper insertion slot, then
reload paper.
error Reload paper.
Pull out the paper set
lever to remove the
paper. Print head
cleaning automatically
starts. After cleaning,
reload paper.
Note the error number,
and turn the printer off
and then on. If the
message remains,
contact EPSON.
Contact EPSON for
service.
Turn the printer off and
then on again.
After 3 seconds, the
message disappears.
Press the Pause button
to exit SelecType mode.
If the message appears
again, clear the error
before you print.
If you are installing ink
cartridges for the first
time, you must install
the cartridges that came
with the printer. If you
are replacing ink
cartridges, check the
package and product
code.

Printing a Status Check

The status check shows the current default settings, amount of
ink remaining in each cartridge, page count, and the status of
various printer parts.
Follow these steps to print the status check:
1. Load a sheet of paper in the printer. (You can print test
pages on roll paper, but you will waste paper.)
2. Press the
SelecType
see

TEST PRINT MENU

3. Press the button until you see
Item
on the display.

CHECK=PRINT

4. Press the button. The status check prints. The
Enter
amount of ink left or component life is indicated as follows:
= full (or full life remaining)
E*****F
= 3/4 full (or 3/4 life remaining)
E**** F
= 1/2 full (or 1/2 life remaining)
E*** F
= 1/4 full (or 1/4 life remaining)
E** F
= nearly empty (or service life near end)
E* F
= empty (or service life ended)
E F
5. Press the
SelecType
Checking Ink Levels and
Component Life
You can view printer status information on the control panel
display without printing a status check. Follow these steps:
1. Press the
SelecType
see

PRINTER STATUS MENU

2. Press the button. You see
Item
the display (indicates the firmware version installed).
3. Continue pressing the
remaining for each of the 6 inks or life remaining for a
number of printer parts. The indicators read as follows:
= full (or full life remaining)
E*****F
= 3/4 full (or 3/4 life remaining)
E**** F
= 1/2 full (or 1/2 life remaining)
E*** F
= 1/4 full (or 1/4 life remaining)
E** F
= nearly empty (or service life near end)
E* F
= less than 10% of ink or service life remaining
<nn>%F
5/01
EPSON Stylus Pro 10000
button on the control panel until you
on the display.
STATUS
button to exit the Test Print menu.
button on the control panel until you
on the display.
VERSION <number>
button to display the amount
Item
EPSON Stylus Pro 10000 - 9
on