Download  Print this page

System Requirements; Control Panel - Epson Stylus Pro 10000 Product Information

Epson stylus pro 10000: product information
Hide thumbs

Advertisement

Table of Contents

System Requirements

®
Macintosh
For USB connection: Power Macintosh
iMac
series (System 8.5.1 through 9.1; System 9.1
recommended) with a compliant USB port and a shielded
USB "AB" cable from Series A (computer) to Series B
(printer) up to 6.6 ft (2 m) long
For IEEE 1394 connection: iMac DV, G3, or G4 series
(System 8.6 or later with FireWire Update 2.1 or later;
System 9.1 recommended) with a compliant IEEE 1394
port and a shielded IEEE 1394 cable
For 10/100 BaseT Ethernet connection: iMac, G3, or G4
series (System 8.5.1 through 9.1; System 9.1 recommended)
with a network cable
350 MHz or higher processor
256MB of RAM
At least 50MB free hard disk space to install the software,
and at least 150MB free hard disk space for processing files
(2GB or more recommended)
Quad-speed (4×) or faster CD-ROM or DVD drive for
installing the printer software
Note:
If you are not using Photo Printing Accelerator in your driver, or if you
are using a software or hardware RIP, you must have a Power
Macintosh G4 with a 500 MHz or higher processor and 512MB RAM
to keep the printing running at full engine speed.
Windows
For parallel connection: IBM
Windows 95, 98, Me, NT 4.0, or 2000; a high-speed
bidirectional, IEEE-1284 compliant parallel cable, 6 to 10
ft (1.8 m) long, with a D-SUB, 25-pin, male connector for
the computer and a 36-pin, Centronics
connector for the printer
For USB connection: IBM-compatible PC running
Windows 98, Me, or 2000 with a Windows compliant USB
port and a shielded USB "AB" cable from Series A
(computer) to Series B (printer) up to 6.6 ft (2 m) long
For IEEE 1394 (FireWire) connection: IBM-compatible
PC running Windows Me or 2000, with a compliant IEEE
1394 port and a shielded IEEE 1394 cable
For 10/100 BaseT Ethernet connection: Ethernet equipped
PC running Windows 95, 98, Me, NT 4.0, or 2000, with a
network cable
®
Pentium
II 400 MHz or higher processor
®
G3, G4, or
®
-compatible PC running
®
compatible
256MB or RAM
At least 50MB of free hard disk space to install the software,
and at least 150MB of free hard disk space for processing
files (2GB or more recommended)
Quad-speed (4×) CD-ROM or DVD drive for installing the
printer software
Note:
If you are not using Photo Printing Accelerator in your driver, or if you
are using a software or hardware RIP, you must have a Pentium III
700 MHz or higher processor with 512MB RAM to keep the printer
running at full engine speed.

Control Panel

display
Control Panel Buttons and Functions
Button
Power
Cleaning
Pause (Reset 3 Sec.)
SelecType
Paper Source (Item)
5/01
EPSON Stylus Pro 10000
Function
Turns the printer on and off.
Runs print head cleaning when pressed for
3 seconds.
Stops printing temporarily. Press a second
time to resume printing.
Clears print data from the printer memory if
pressed and held for three seconds.
Returns the printer to READY status when
pressed in SelecType mode.
Causes the printer to enter SelecType mode
when pressed in READY status.
In SelecType mode, this button can be used
to select a desired menu.
Selects the paper source:
Roll Auto Cut
Cutter Off
, or
Sheet
. If you press this button
during the ink drying process, you will need to
press
Enter
to select your setting.
In SelecType mode, this button can be used
to select an item in a menu.
EPSON Stylus Pro 10000 - 7
,
Roll

Advertisement

Table of Contents
loading

  Related Manuals for Epson Stylus Pro 10000