Download  Print this page

Epson Stylus Pro 10000 Product Information page 8

Epson stylus pro 10000: product information
Hide thumbs

Advertisement

Table of Contents
EPSON Stylus Pro 10000
Button
Function
Paper Feed
(+)
Feeds paper in reverse.
In SelecType mode, a desired parameter can
be selected for the item (forward order).
Paper Feed
(–)
Feeds paper forward.
In SelecType mode, a desired parameter can
be selected for the item (reverse order).
Cut/Eject (Enter)
Ejects the cut sheet when the
on.
Feeds the roll paper before cutting it when the
Roll Auto Cut
Feeds the roll paper a small amount when the
Roll Cutter Off
Feeds the roll paper and then prints a page
line below the document when the
light and
Off
In SelecType mode, sets the selected
parameter for an item as the default value.
Control Panel Lights and Messages
Normal printer operation
Display Message/Light
/
light on
READY
Operate
/
light
PRINTING
Operate
flashing
/
INK DRY <number> MIN
Pause
light flashing
/
INK CHARGING <number>%
Pause
light on or flashing
/ all lights flash briefly
RESET
/
PRESS PAUSE BUTTON
Pause
light on
/
light on or
WAIT
Pause
flashing
PAUSE/ Pause
light on
NO INK CARTRIDGE
PAT PRINTING
/
Operate
light
flashing and
Pause
light is on
POWER OFF
/
Operate
light is
flashing
Error conditions
Display
Message/Light
Explanation
/
Lower cover is open.
COVER OPEN
Pause
light on
You are replacing the ink
INK COMPART.
OPEN
/
Pause
cartridge(s) and the ink
light on
compartment cover is
open.
INK LOW
/
Ink Out
Ink cartridge(s) are
light(s) flashing
nearly empty (printing
continues).
8 - EPSON Stylus Pro 10000
light is
Sheet
light is on.
light is on.
Roll Cutter
option are on.
Print Page Line
Explanation
Printer is ready to print.
Printer is receiving data.
Printer is paused to let ink dry. Wait
for the number of minutes shown.
Printer is charging ink.
Printer is resetting.
Press the
button to continue.
Pause
Printer is warming up, performing
maintenance, or charging ink.
Printer is paused. To resume printing,
press the
Pause
button.
Appears when an ink cartridge is
being replaced.
Print head alignment pattern is
printing.
Printer is shutting down.
Response
Close the lower cover.
Close the ink
compartment cover
when you are finished
replacing the ink
cartridge(s).
Replace ink cartridge(s)
indicated by
Ink Out
light(s). See page 10.
Error conditions (continued)
Display
Message/Light
Explanation
/
Ink cartridge(s) are
INK OUT
Ink Out
light(s) on
empty (printing stops).
/
Paper is being loaded,
LOAD PAPER
light
and the paper set lever
Paper Out
on
is out, in the released
position.
Paper source setting in
LOAD ROLL
PAPER
or
print options is different
from control panel.
LOAD SHEET
/
PAPER
Paper
light on
Out
MAINTENANCE
A printer part will need
REQ. <error
to be replaced soon.
number>
MAINTENANCE
The waste ink system is
REQ 0100
almost full.
Ink cartridge(s) not
NO INK
/
installed.
CARTRIDGE
Ink
Out
light(s) on
NOZZLE CHECK
The printer was unable
ERROR
to clean the nozzles
when it was powered
on, or before beginning
a print job.
OPTION I/F
Wrong interface card
ERROR
installed.
/
Paper has jammed in the
PAPER JAM
Paper Out
light
printer.
flashing
PAPER NOT CUT
/
Roll paper was not cut
light
completely.
Paper Out
flashing
Cut paper did not fall off.
Paper slipped and fed
PAPER NOT
/
into the printer at an
STRAIGHT
Paper Out
light
angle.
flashing
PAPER OUT
/
No paper is loaded.
light
Paper Out
Paper ran out.
on
LOWER PAPER
Paper set lever was
SET LVR
/
Paper
released during the
light on
Out
printing process or
another operation.
5/01
Response
Replace ink cartridge(s)
indicated by
Ink Out
light(s). See page 10.
Push the paper set lever
in after you load the
paper.
Make sure the right
paper is loaded and the
paper source setting is
the same on the control
panel and print options.
Note the error number
and contact EPSON.
Contact EPSON to
schedule service.
Install ink cartridges as
indicated by the lights.
See page 10.
Turn the printer off and
then on again. When the
automatic nozzle check
is enabled (default), the
printer automatically
runs a nozzle check and
cleaning cycle each time
it is turned on.
Turn off the printer and
remove the card.
Remove the jammed
paper. Then turn the
printer off and on again.
Cut the paper manually,
then remove the cut
paper from the printer.
Reload paper.
Remove the cut paper
from the printer. Reload
paper.
Reload paper, making
sure the edges are
straight and aligned with
both rows of holes.
Load paper.
Remove any paper in
the printer and load
more paper. If the
message appears during
a print job, press the
button for 3
Pause
seconds to reset the
printer. Then load paper
and resend the job.
Push in the paper set
lever. Start printing again
from the beginning for
best results.

Advertisement

Table of Contents
loading

  Related Manuals for Epson Stylus Pro 10000