Table of Contents
Advertisement
Quick Links
Quick Start
Overview
This quick start describes how to install, configure, and troubleshoot the NetVanta 1560-08-65W, 8-port Managed GbE 65W PoE+ Switch. Figures 1 and 2 show the Front and
Rear Panel layouts of the switch.
■
"Installing the Switch"
on page 1
■
"Initially Configuring the Switch"
■
"Power Over Ethernet (PoE)"
on page 6
■
"Understanding the Status LEDs"
■
"Using the MODE Button"
on page 7
■
"Troubleshooting the Switch"
on page 7
Installing the Switch
g
NOTE
Refer to the national, state and local electrical codes for the requirements for power, grounding, wiring, and installation methods.
f
WARNING!
Read all warnings, cautions, notes and installation instructions before installing or servicing this equipment.
Package Contents
■ NetVanta 1560-08-65W switch
■ AC power cord
■ DB-9 to RJ-45 cable
■ Micro-USB to USB cable
■ Four adhesive rubber feet
■ Quick Start
NetVanta 1560-08-65W
8-port Managed GbE 65W PoE+ Switch
on page 5
on page 6
Figure 1. Front Panel Layout
LINK/ACT/SPD
SYS
Mode LED
LED
SYSTEM
NetVanta 1560-08-65W
LNK/ACT/SPD
PoE
PoE
Mode LED
Figure 2. Rear Panel Layout
CONSOLE
10/100/1000
Port
RJ-45 with PoE+
USB
MODE/RESET
CONSOLE
1
2
3
4
5
MODE
Port Status
Button
AC Line: 100-240V 50-60Hz
Power Connection
100/1000 RJ-45/SFP
Combo Ports
6
7
8
9
10
9
10
LEDs
AC Line: 100-240V 50-60Hz
June 2020
617101561PF2-13A
P/N: 17101561PF2
Advertisement
Table of Contents
Related Manuals for ADTRAN NetVanta 1560-08-65W
Summary of Contents for ADTRAN NetVanta 1560-08-65W
- Page 1 Quick Start P/N: 17101561PF2 Overview This quick start describes how to install, configure, and troubleshoot the NetVanta 1560-08-65W, 8-port Managed GbE 65W PoE+ Switch. Figures 1 and 2 show the Front and Rear Panel layouts of the switch. ■ “Installing the Switch”...
- Page 2 CAUTION! The NetVanta 1560-08-65W is intended for indoor use only. Ethernet, PoE cables, and attached equipment are intended for use within the same building with equipotential bonding, and not intended to be placed in separate buildings or structures. Failure to deploy as described could result in permanent damage from lightning or other electrical events and voids the warranty.
- Page 3 2. Slide the keyed insets on the bottom of the unit’s chassis securely onto the screws. Figure 7. Attaching the Switch to the Wall CAUTION! The NetVanta 1560-08-65W must be mounted in the face down orientation when wall mounted. 617101561PF2-13A...
- Page 4 This product is intended for use with a Class 1 Laser module that complies with FDA 21 CFR 1040.10, 1040.11 and IEC 60825-1. For continued compliance with the above standards, only approved Class 1 Laser modules from an ADTRAN approved vendor list (located on the ADTRAN website) should be installed in this product. ADTRAN cannot certify system integrity with other laser modules.
-
Page 5: Initially Configuring The Switch
Initially Configuring the Switch The Switch can be configured by two methods: ■ Web based Graphical User Interface (GUI) ■ Command Line Interface (CLI) Initial Switch Configuration Using a Web Browser After powering up the switch for the first time, you can perform the initial switch configuration using a web browser. To begin with the initial configuration stage, you need to reconfigure your PC’s IP address and subnet mask to make sure the PC can communicate with the switch. -
Page 6: Power Over Ethernet (Poe)
Power Over Ethernet (PoE) The switch provides the PoE on the eight Ethernet ports shown in Figure 1. PoE provides the ability to detect attached Powered Devices (PDs), and deliver power to the PD via Ethernet cabling. The switch is fully compliant with the IEEE 802.3af PoE and IEEE 802.3at PoE+ standards. By default, the PoE switch discovers and provides power to IEEE- compliant PDs, it also supports legacy PDs. -
Page 7: Using The Mode Button
2. This device must accept any interference received, including interference that may cause undesired operation. ■ Changes or modifications not expressly approved by ADTRAN could void the user's authority to operate this equipment. ■ Changes or modifications not expressly approved by ADTRAN will void the warranty. - Page 8 ASE Command Reference Guide ADTRAN CUSTOMER CARE: Warranty: ADTRAN will replace or repair this product within the warranty period if it does not From within the U.S. 1.888.423.8726 meet its published specifications or fails while in service. Warranty information can be found online at www.adtran.com/warranty.