Page 1
User Guide IU 5300-S Converged Network Appliance V7.2.2 — May 2007...
Page 2
As between the parties, Polycom, Inc. retains title to, and ownership of, all proprietary rights with respect to the software contained within its products. The software is protected by United States copyright laws and international treaty provision.
Introduction Introducing the V IU 5300-S Converged Network Appliance Installed at the edge of the operations center, 5300-S Series converged network appliances secure critical voice, video and data infrastructure components such as VoIP softswitches, video Gatekeepers, gateways and media servers. This chapter contains the following sections: •...
Page 8
User Guide V IU 5300-S Series Converged Network Appliance The 5300-S Series converged network appliances can be deployed in service provider or enterprise environments as depicted below. Service Provider ISDN, PSTN PSTN Network H.323 Gatekeeper Softswitch Gateway 5300-S Aggregation Router Hotspot NAT/Firewall Public IP...
Page 9
Introduction Headquarters H.323 Application Softswitch Gatekeeper Server IP Phone PSTN 5300-S 5300-E Gateway IP Phone IP Phone Aggregation Router PSTN PSTN Network T-1/E-1 NxT-1/E-1 Branch Office Aggregation Company B Router 5300-E 4300T H.323 Endpoint Gateway H.323 Gateway IP Phone Laptop IP Phone EM009A The 5300-S is designed to protect managed VoIP service providers and...
User Guide V IU 5300-S Series Converged Network Appliance Features • Resolves firewall traversal problems at the Network Operations Center for VoIP by providing a VoIP application layer gateway (ALG) or voice and video aware firewall that supports SIP, MGCP and H.323 •...
Introduction Management Features The 5300-S is configured and managed through the Configuration Menu, a web-based Graphical User Interface. Access the Configuration Menu by entering a URL in a web browser such as Internet Explorer, Netscape, or Firefox. Using the Configuration Menu, you can set a wide range of network services, including: •...
Page 12
User Guide V IU 5300-S Series Converged Network Appliance 1 - 6...
Installing the 5300-S The 5300-S is designed for a 19-inch rack mount installation. Before installing, note the following cautions: • Never assume that the AC cord is disconnected from a power source. Always check first. • Always connect the AC power cord to a properly grounded AC outlet to avoid damage to the system or injury.
Page 14
User Guide V IU 5300-S Series Converged Network Appliance 2 - 2...
Configuring the V IU 5300-S Configure the Polycom V IU 5300-S using a web browser such as Internet Explorer or Netscape Navigator. The 5300-S is shipped with a pre-configured IP address for its Subscriber (Port 1) interface. This chapter includes the following sections: •...
Page 16
User Guide V IU 5300-S Series Converged Network Appliance 3. Press Return. The Main Configuration Menu appears. 4. To log in, select Network from the navigation bar. 5. In the Connect to pop-up enter the following default information: — For username: root —...
Configuring the V IU 5300-S 6. Continue to configure the system using the information provided in subsequent chapters of this guide. Logging In and Out of the 5300-S You are prompted to log in every time you point a new browser session to the Configuration URL.
User Guide V IU 5300-S Series Converged Network Appliance Menu Description Network Through the Network page, you can configure a wide range of multimedia network services. These services can be enabled or disabled depending on the functionality required for a network configuration.
Configuring the V IU 5300-S Note: All open web browsers must be closed when you change between administrative user “root” and read-only “rouser.” 4. Enter a new password. The password must be a minimum of six characters long. 4. Re-enter the new password to confirm it. 5.
User Guide V IU 5300-S Series Converged Network Appliance 2. In the System menu, select Network Information. 3. Scroll through the Network Information page to view: — Routing information — Link status — Interface information Routing Information The system routing table contains the static routes for the hosts and networks that are on the Provider side of the 5300-S.
Configuring the V IU 5300-S Link Status Link Status displays the status of the Ethernet connections. Ethernet auto negotiation is often unreliable, especially between different vendors or old and new networking equipment. Failure of auto negotiation is generally not a cause for concern.
User Guide V IU 5300-S Series Converged Network Appliance 2. In the System menu, select System Information. 3. Scroll through the System Information page to view: — System uptime — Number of active streams — Recent call log — Process information —...
Configuring the V IU 5300-S Recent Call Log The Recent Call Log displays quality information about calls that are in progress or have recently completed. If a call falls below the configured MOS Threshold, a system log message is created. The MOS score for a call is always displayed when the call is completed.
Page 24
User Guide V IU 5300-S Series Converged Network Appliance 3 - 10...
Configuring Network Settings This chapter describes how to configure the 5300-S network settings. It contains the following sections: • Configuring Subscriber Interface Settings • Configuring Provider Interface Settings • Subinterfaces • ToS Byte Setting • Setting the Ethernet Link Rate •...
User Guide V IU 5300-S Series Converged Network Appliance To configure subscriber interface settings: 1. In the navigation bar, select Network. 2. In Subscriber Interface Settings, highlight and replace the default IP Address and Subnet Mask. 3. If you are configuring network settings, see the instructions in Configuring the Network on page 4-8.
Configuring Network Settings To configure provider interface settings: 1. In the navigation bar, select Network 2. In Provider Interface Settings, select Static IP Address (the most common configuration), or DHCP if a DHCP server assigns the 5300-S internal address. 3. Enter an IP Address. 4.
How Subinterfaces Works A common use for subinterfaces is forwarding a public subnet. A subinterface may be created to support a subnet forwarded through the Polycom V 5300-S. When forwarding a subnet through the Polycom V IU 5300-S, it is necessary to assign an address for this subnet to the system to act as the subnet's gateway.
How the ToS Byte Setting Works For all RTP traffic (voice and video), the Polycom V IU 5300-S marks the ToS byte in the IP header as “High Priority,” and strips (set to 0) the ToS byte for all other traffic.
User Guide V IU 5300-S Series Converged Network Appliance Viewing or Changing the ToS Byte Setting To view or change the ToS byte setting, use the following steps: 1. Using the configuration graphical user interface, from the Configuration Menu on the left-hand side, click Traffic Shaper. 2.
Page 31
Configuring Network Settings The link rate of an interface can be assigned to a desired rate. A network administrator may want to set the rate manually if autonegotiation fails to select a rate consistently or if it selects a rate that is slower than the maximum rate supported by both interfaces.
User Guide V IU 5300-S Series Converged Network Appliance Setting Description 100baseT-HD 100Mbits per second using half duplex transmission 100baseT-FD 100Mbits per second using full duplex transmission Autonegotiate The 5300-S autonegotiates link rate and duplex with the directly attached device. 5.
Page 33
Configuring Network Settings 2. Enter an IP address for the Default Gateway This must be the next-hop-router connected to Port 1, the Subscriber side interface 3. Enter the Primary DNS Server. 4. Enter the Secondary DNS Server. 5. Press Submit. 4 - 9...
Page 34
User Guide V IU 5300-S Series Converged Network Appliance 4 - 10...
Configuring for Video This chapter describes how to configure the Polycom V IU 5300-S to support video: • H.323 Configuration • Forwarding Rules • Peering Proxy • Clients List Lock • H.323 Activity Monitor • H.460 Operation Mode 4 - 1...
User Guide V IU 5300-S Series Converged Network Appliance H.323 Configuration To access the H.323 Settings page, select VoIP ALG > H.323 in the Configura- tion Menu. 4 - 2...
Page 37
Configuring for Video The H.323 Settings page has the following areas: • Gatekeeper Mode • WAN/Provider-side gatekeeper mode settings • LAN/Subscriber-side gatekeeper mode settings • Embedded gatekeeper mode settings LRQ Size • Default Alias • Stale Time • • Multicast Messages 4 - 3...
Page 38
User Guide V IU 5300-S Series Converged Network Appliance • H.460.18 Support • Alias Restrictions In the Gatekeeper mode area, select one of the following modes: Item Description None H.323 is disabled. WAN/Provider-side Specifies that the system will forward all client RAS gatekeeper mode messages to the gatekeeper.
Page 39
Configuring for Video If LAN/Subscriber-Side Gatekeeper mode is selected, you must configure the following parameters: Item Description LAN/Subscriber-side GK Enter the IP address of the gatekeeper. address Allow public IP in LCF Select the checkbox if the gatekeeper has been deployed with multiple outbound proxies and must decide which proxy to use based on the IP address returned in the LCF.
Page 40
User Guide V IU 5300-S Series Converged Network Appliance Some RAS messages can be multicast in order to automatically detect gate- keepers. In the Multicast Messages area, you can enable listening to multicast messages. This area includes the following configurable parameter: Item Description Listen to multicast...
Configuring for Video H.323 Activity To access the H.323 Activity page, select VoIP ALG > H.323 Activity in the Configuration Menu. The H.323 Activity page is a read-only page that shows the following infor- mation: • Current time • WAN Gatekeeper status •...
Page 42
User Guide V IU 5300-S Series Converged Network Appliance To access the H.323 Alias Manipulation page, select VoIP ALG > H.323 >Alias Manipulation in the Configuration Menu. This page includes the following areas: Item Description Destination Lists alias manipulation rules. H323-ID or Rules are executed in the order in which they are listed.
Configuring for Video The H.323 Alias Manipulation page includes the following buttons: Item Description Commit Applies the settings configured on this page. Reset Clears all fields and selections and allows you to enter new information. H.323 Neighboring Neighboring and prefix routing can be used to route calls based on a match- ing prefix in the destination alias of the call.
Page 44
User Guide V IU 5300-S Series Converged Network Appliance This page includes the following areas: Item Description Prefix Routing Lists rules for forwarding incoming calls based on their dialed alias. Gatekeeper Rules are executed in the order in which they are listed. Use the Neighboring arrows to move entries up and down, or use the Index field to table...
Configuring for Video Regular Expressions Alias manipulation patterns and prefixes use regular expressions to match a string in the destination alias. A regular expression can be a string of literal characters to match or a set of special expressions. Alias manipulation patterns can match a sub-string at any location and number of times within the alias.
How Forwarding Rules Works When forwarding, one address from the forwarded range of addresses must be assigned to the rule's output interface. The Polycom V IU 5300-S uses this address to act as a gateway router for the subnet. The address may be assigned using the Subinterfaces page.
Configuring for Video Configuring Forwarding Rules To configure address forwarding rules, use the following steps: Using the configuration graphical user interface, from the Configuration Menu on the left-hand side, click Firewall. Click Forwarding Rules. The window shown below opens. 4 - 13...
Page 48
User Guide V IU 5300-S Series Converged Network Appliance On this screen, complete the following information: IP Subnet: The subnet to be forward through the firewall from the Input • Interface to the Output Interface. Netmask: The network mask to apply to the IP Subnet to create the range •...
The illustration below shows a sample diagram with dial plan and call flow examples. It is a snapshot of how the Peering Proxy can be deployed. Peering Proxy however, is not limited to this specific scenario, so contact your Polycom representative to discuss specific network requirements for full Peering Proxy support.
Page 50
1 prefix pointing to the master gatekeeper and let that gatekeeper signal the other endpoints directly. In the example above, the Polycom V IU 5300-S Peering Proxy is installed in “Private Video Network A and B,” a peering point into this network. This network could have additional peering points to allow topology spreading of network resources.
Page 51
Configuring for Video Proxy provides an access point into this network and is responsible for the E.164 dial plan using NANP (North American Numbering Plans or NPAs). The NPAs in this case are 831 and 408. Dial plan integrity is required to insure proper routing of prefix's. This means that if users are to dial into your network, they could be required to enter a “Prefix”...
Page 52
User Guide V IU 5300-S Series Converged Network Appliance the Peering Proxy IP 10.10.10.1. The Peering Proxy applies the same rule set, in this case, NO matching prefix is found and ANNEX O dialing is applied. The call is now routed to Site A's V IU.
Configuring for Video Embedded Gatekeeper Mode. In this mode, the endpoint is directly registered, an E.164 registered client match is made, and the call is routed to the called endpoint. Outbound from Site C to Public IP Endpoint Site C dials the public endpoint: 9@61.10.10.4. The PathNavigator receives the call and generates a Q.931 setup to the V IU for that subnet.
User Guide V IU 5300-S Series Converged Network Appliance 3. On this screen, check “Peering-Proxy mode”. 4. Scroll to the bottom of the window and click Submit. Adding an H.323 Prefix Entry You can add prefixes by entering the prefix string and the target address. To add an H.323 prefix entry, use the following steps: 1.
Configuring for Video The prefix routing table shows all currently configured prefixes. The prefixes are searched in the order they are entered. Each prefix can be moved up or down in the list. You can select and delete prefixes. 3. To strip a matching prefix, select the checkbox and click Submit. If you enable this, all matching prefixes are stripped from the destination alias before the call is forwarded.
User Guide V IU 5300-S Series Converged Network Appliance — Manually entering all clients that are allowed to use the system — Running the system without the Client List lockdown feature until all desired clients have registered • Enabling this feature. This feature is useful for lists involved with 911 usage.
Configuring for Video H.323 Activity Monitor The H.323 Activity Monitor shows any recent H.323 events that may be of interest to the administrator of the system. The information appears in three columns: • Event/Time • Source • Destination Following this information are a number of lines with event specific informa- tion such as call-id, duration, call-status, and so on.
User Guide V IU 5300-S Series Converged Network Appliance Type of Events The events that may currently be listed in the activity monitor are as follows: • Bandwidth change - the endpoint requested a change of the bandwidth used for its call, only sent if the bandwidth management is enabled. •...
Page 59
Configuring for Video • “Attempting to establish outgoing Q.931 TCP connection” Successfully resolved the destination of the call and attempting to establish an outgoing Q.931 TCP connection to the destination. • “Q.931 signaling received and forwarded” Both Q.931 TCP connections have been successfully established and Q.931 signaling has been received and forwarded.
User Guide V IU 5300-S Series Converged Network Appliance Call Termination The call termination cause may also give some information about why the call terminated or failed to be established. • “Out of system resources” The call could not be completed because the system was out of system resources.
Configuring for Video The call could not be established because the system already is at the maxi- mum allowed bandwidth. • “Received admission reject” The call was terminated because an admission reject was received from the gatekeeper. • “Received disengage request” The call was terminated because the endpoint requested to tear down the call.
User Guide V IU 5300-S Series Converged Network Appliance H.460 Operation Mode This feature allows the Polycom V IU 5300-S to do NAT/Firewall traversal for clients behind NAT or firewall devices. The endpoint must always signal H.460.18 capability for this feature to be enabled.
Page 63
Configuring for Video Gatekeeper Video User D IU-S Video User E Video User C Internet NAT/Firewall NAT/Firewall Trusted Video User A Video User F Video User B H.323 requires many connections in order to establish a call, for example, Q.931 and H.245 TCP connections and multiple RTP UDP streams. H.460.18 allows an H.323 device to traverse a NAT/Firewall by having the private-side endpoint initiate all TCP connections and UDP streams to the outside H.323 device.
User Guide V IU 5300-S Series Converged Network Appliance The connection between User D and User A is hairpinned. This means that the connection is 768 kilobits per second (kbps) or 2 times 384 kbps, the typical bandwidth for a H.323 call. •...
Page 65
Configuring for Video 3. Scroll down until the following part of the window appears. 4. On this screen, use the following options: — Disabled – disabled (The system will not use H.460.18 even though the endpoint is capable of it.) —...
Page 66
User Guide V IU 5300-S Series Converged Network Appliance 4 - 32...
Configuring VoIP This chapter describes how to configure VoIP capabilities. It contains the following sections: • Overview • Configuring VoIP Subnet Routing • Configuring VRRP • Configuring VRRP • Configuring VRRP Overview An application-layer gateway provides basic proxy features for voice and video over IP traffic.
Page 68
User Guide V IU 5300-S Series Converged Network Appliance To configure VoIP ALG: 1. In the navigation bar, select VoIP ALG. 2. On the VoIP ALG page, enter information as follows: Field Description MGCP Server IP Address If a MGCP ALG is needed, enter the IP address for the MGCP Server as provided.
Page 69
Configuring VoIP Field Description SIP Server Address The SIP server provides session-initialization protocol service to IP phones, client adapters and gateways. If a SIP ALG is needed, enter the address (either an IP or URL) for the SIP Server. This address should be reached via the Provider side Ethernet port.
Page 70
User Guide V IU 5300-S Series Converged Network Appliance Field Description SIP Register pacing If the SIP Expires override field is set to a lower value, the number of registration messages may overload the soft-switch. In order to prevent this, you can set the SIP Register pacing field to the number of seconds to wait before forwarding a register message from one phone to the...
Page 71
Configuring VoIP Field Description Automatic MGCP Audit The Automatic MGCP Audit flag specifies whether MGCP clients should be automatically audited by sending a message to each client and wait for a response. Audit Cycle Interval The Audit Cycle Interval specifies how often these messages should be sent out to the clients.
User Guide V IU 5300-S Series Converged Network Appliance Field Description SIP LAN side Gateway The SIP LAN Side Gateway is used to configure a LAN side SIP gateway to which calls that are not for a registered phone can be sent. The name of the gateway is a locally meaningful name.
Configuring VoIP 2. In the System menu, select VoIP Subnet Routing. 3. Enter the network address in IP Network, such as 10.10.12.0. This is the IP address of the remote subnet containing the voice devices. 4. Enter a subnet mask in Netmask, such as 255.255.255.0 A subnet mask of the network determines which packets are destined for the 5300-S.
User Guide V IU 5300-S Series Converged Network Appliance Configuring VRRP The Virtual Router Redundancy Protocol (VRRP) is designed to eliminate the 5300-S as a single point of failure in a network configuration. Two 5300-S devices can be configured to perform as a redundant pair. One 5300-S is the Master, the other is the Backup.
Page 75
Configuring VoIP 10. Enter the Gratuitous ARP Delay. How long in seconds an 5300-S should wait after a switch over before sending Gratuitous ARPs packets. 11. Press Submit. 5 - 9...
Page 76
User Guide V IU 5300-S Series Converged Network Appliance 5 - 10...
Configuring the Firewall This chapter describes how to configure the 5300-S as a firewall. It contains the following sections: • Configuring Basic Firewall Settings • Configuring Advanced Firewall Settings The 5300-S can act as a firewall. A firewall restricts and controls the traffic between networks, typically between a corporate network and the Internet.
Page 78
User Guide V IU 5300-S Series Converged Network Appliance To configure basic settings: 1. In the navigation pane, select Firewall. 2. In the section: Basic LAN and WAN Firewall Settings, enable the management services that you want to reach the 5300-S by checking the appropriate box for: —...
Configuring the Firewall Basic settings rules Follow these rules when configuring basic settings: • For Allow TCP Port and Allow UDP Port, valid values are 1 through 65535. • Separate multiple entries by spaces, • Indicate a range of values with a colon (:). For example, 25:50 means perform the action on ports 25 through 50 Configuring Advanced Firewall Settings A comprehensive security policy can be created using advanced settings.
User Guide V IU 5300-S Series Converged Network Appliance 4. Configure Deny Hostwise TCP (IP-Port) according to the rules in Advanced setting rules on page 6-4. This setting denies all traffic matching the specified TCP port numbers and the specified source IP addresses 5.
Administrative Options The 5300-S supports a number of additional administrative operations. This chapter contains the following sections: • Changing the Administration Password We strongly recommend that you change the default password for the root administrative account. To change the password: 1.
User Guide V IU 5300-S Series Converged Network Appliance 2. On the System page, locate Change Password, and follow this link: The password of the device can be changed. 3. Enter the New Password. The new password must be between 6 and 20 characters in length.
Administrative Options To enter a user command: 1. Choose User Commands from the System menu on the navigation bar. 2. Enter a command in the User Commands: area. 3. Press Submit. 4. Restart the network to guarantee that the user commands are running. Restarting the Network on page 7-6.
User Guide V IU 5300-S Series Converged Network Appliance To work with the client list: 1. Choose Clients List from the System menu on the navigation bar. 2. Select a protocol from Protocol to display. The SIP client list is the default. 3.
Administrative Options 2. Press OK to delete the client or Cancel to end the operation. Querying clients To query a client: 1. Click the Information Icon in the No Sort column. 2. Details about the selected client display at the top of the page. Adding clients To add a client: 1.
User Guide V IU 5300-S Series Converged Network Appliance Press Submit. Restarting the Network Use Network Restart to stop and the restart all the networking services that are running on the system. Technical support may request that networking services be restarted during a troubleshooting session. Restarting network services will interrupt the system for up to a minute.
Administrative Options Running a ping test The Ping Test is the most common test used to verify basic connectivity to a networking device. Successful ping test results indicate that both physical and logical path connections exist between the 5300-S and the test IP address. Successful ping tests do not guarantee that all data message are allowed between the 5300-S and the test IP address.
User Guide V IU 5300-S Series Converged Network Appliance 2. In the System menu, select Network Test Tools. 3. Enter an IP Address to Trace 4. Select an Interface. 5. Press Traceroute. Upgrading the Firmware Occasionally, new releases of firmware will become available to add new features to the 5300-S.
Administrative Options To upgrade the firmware: 1. In the navigation bar, select System. 2. In the System menu, select Upgrade Firmware. 3. Enter an Download Server IP address. 4. Enter a Filename. 5. Press Submit. Configuring a Management Interface You can configure a specific management interface and restrict management of the system to this interface only.
User Guide V IU 5300-S Series Converged Network Appliance 2. On the System menu, select Management Interface. 3. On the Management Interface page: 4. Check the Enable Management Interface box. 5. Enter a Management Interface IP Address. 6. Enter a Subnet Mask address. 7.
Administrative Options 1. Reconnect the 5300-S to the network by moving the connection from the Provider port (Port 2) to the Optional Out of Band Ethernet Port (Port 3). Figure 1. Move the connection from Port 2 to Port 3 2.
User Guide V IU 5300-S Series Converged Network Appliance To configure trusted management addresses: 1. In the navigation pane, select Firewall. 2. Within the Trusted Management Addresses, enter a list of trusted management host addresses or network/masks. The basic firewall rules will be applied only to those addresses.
Administrative Options Caution When manually configuring the MTU size we recommend that you use a setting of 800 bytes or greater. You may experience problems with certain types of VoIP traffic if the MTU size is set below 800 bytes. To set the Provider MTU size: 1.
Page 94
User Guide V IU 5300-S Series Converged Network Appliance 2. In the System menu, select Services Configuration. 3. Enter information as described in the following table. Field Description SNMPv1 Read-Only Community The community string that the management station uses when accessing read-only objects from the 5300-S.
Administrative Options Field Description SNMPv3 Security The SNMPv3 security level for user authentication and encryption of both synchronous requests as well as asynchronous traps. None means neither SNMPv3 authentication or encryption are used. Auth(MD5) means authenticating user using MD5 hash algorithm. AuthPriv(MD5/DES) means authentication as well as encryption using the DES encryption algorithm.
Page 96
User Guide V IU 5300-S Series Converged Network Appliance 2. In the System menu, select Services Configuration. 3. Scroll to Enable Remote System Logging, and check the box. 4. Enter information as described in the following table: Field Description Remote Syslog Host: The address of the system running a system log server.
Administrative Options Disabling remote system logging To disable remote system logging, select Services Configuration from the System menu and uncheck Enable Remote System Logging. Setting the System Date and Time The System Time page allows the user to set the 5300-S's time or configure it to synchronize with a network time source via Simple Network Time Protocol (SNTP).
User Guide V IU 5300-S Series Converged Network Appliance Field Description Month Enter a value from 1 to 12. Enter a value from 1 to 31. Year Enter the current year. Hour Enter a value from 0 (Midnight) to 23 (11 pm).
Page 99
Administrative Options 2. In the System menu, select Route. 3. Check the Apply Route box. 4. Enter an IP Network address. 5. Enter a Netmask address. 6. Enter a Gateway address. 7. Press Submit. To delete a static route, uncheck the Apply Route box. 7 - 19...
Page 100
User Guide V IU 5300-S Series Converged Network Appliance 7 - 20...
Appendix Troubleshooting Tips This section assists you with problems you may encounter while installing the 5300-S. Trouble accessing the Internet We recommend connecting a PC either directly or through a switch to the Port 1 of the 5300-S. The default IP address of the 5300-S is 192.168.1.1 so please be sure that the IP address of the PC is on the same network (eg.
1. From the navigation bar, select System. 2. From Registration Status, click License Key. 3. If you do not see a license key, please contact Polycom Technical Services. Telephone doesn't register with the softswitch If one or more telephones are not registering with the softswitch: •...
Page 103
(and/or any company you represent) and either Polycom (Netherlands) B.V. (in Europe, Middle East, and Africa), Polycom Hong Kong, Ltd. (in Asia Pacific) or Polycom, Inc. (in the rest of the world) (each referred to individually and collectively herein as “POLYCOM”), for the SOFTWARE PRODUCT licensed by POLYCOM.
Page 104
GRANT OF LICENSE. Subject to the terms of this Agreement, POLYCOM grants to you a non-exclusive, non-transferable, revocable license to install and use the SOFTWARE PRODUCT solely on the POLYCOM product with which this SOFTWARE PRODUCT is supplied (the "PRODUCT"). You may use the SOFTWARE PRODUCT only in connection...
Page 105
SOFTWARE PRODUCT are owned by POLYCOM or its suppliers. Title, ownership rights, and intellectual property rights in the SOFTWARE PRODUCT shall remain in POLYCOM or its suppliers. Title and related rights in the content accessed through the SOFTWARE PRODUCT is the property of such content owner and may be protected by applicable law.
Page 106
POLYCOM's option and expense, to refund the purchase price paid by you for any defective software product which is returned to POLYCOM with a copy of your receipt, or to replace any defective media with software which substantially conforms to applicable POLYCOM published specifications.
Page 107
THAT RESULTS FROM THE DOWNLOAD OR USE OF THE SOFTWARE PRODUCT. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT SHALL POLYCOM OR ITS SUPPLIERS BE LIABLE FOR ANY SPECIAL, INCIDENTAL, INDIRECT, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING, WITHOUT LIMITATION,...
Page 108
11.3 Contact. If you have any questions concerning this Agreement, or if you desire to contact POLYCOM for any reason, please contact the POLYCOM office serving your country. 11.4 U.S. Government Restricted Rights. The SOFTWARE PRODUCT and documentation are provided with RESTRICTED RIGHTS.
Page 110
User Guide V IU 5300-S Series Converged Network Appliance You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the Program, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions: a) You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change.
Page 111
Regulatory Notices the corresponding source code, to be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or, c) Accompany it with the information you received as to the offer to distribute corresponding source code.
Page 112
User Guide V IU 5300-S Series Converged Network Appliance conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not distribute the Program at all.
Page 113
Regulatory Notices exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally. NO WARRANTY 11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW.
Page 114
User Guide V IU 5300-S Series Converged Network Appliance Regulatory Notices - 12...