Related Manuals for Polycom TRAPEZE NETWORKS 1725-36060-001
Summary of Contents for Polycom TRAPEZE NETWORKS 1725-36060-001
- Page 1 VIEW Certified Configuration Guide Trapeze Networks Mobility System for MP-422 Access Points June 2008 Edition 1725-36060-001 Version D...
- Page 2 Polycom, Inc. has prepared this document for use by Polycom personnel and customers. The drawings and specifications contained herein are the property of Polycom and shall be neither reproduced in whole or in part without the prior written approval of Polycom, nor be implied to grant any license to make, use, or sell equipment manufactured in accordance herewith.
-
Page 3: Certified Product Summary
SpectraLink Wireless Telephones and wireless LAN (WLAN) infrastructure products. The products listed below have been thoroughly tested in Polycom’s lab and have passed VIEW Certification. This document details how to configure the Trapeze Networks Mobility Exchange (MX) switch and Mobility Point (MP) access point (AP) with SpectraLink Wireless Telephones. -
Page 4: Service Information
For more detailed information on wireless LAN layout, network infrastructure, QoS, security and subnets, please see the Guide for Deploying SpectraLink 8020/8030 Wireless document identifies issues and solutions based on Polycom’s extensive experience in enterprise-class Wi-Fi telephony, and provides recommendations for ensuring that a network environment is adequately optimized for use with SpectraLink 8020/8030 Wireless Telephones. -
Page 5: Network Topology
Network Topology The following topology was tested during VIEW Certification. It is important to note that these do not necessarily represent all “Certified” configurations. Both Layer-2 and Layer-3 roaming were tested. Layer-3 roaming of SpectraLink Wireless Telephones requires the use of a generic routing encapsulation (GRE) tunnel. - Page 6 Access Point Setup and Configuration Installing software Trapeze Mobility Exchange firmware cannot be downloaded from the SpectraLink website. Therefore, you must use the software that was shipped with your product, or contact Trapeze Networks for the latest software release. Command, comment, and screen text key In the sections below you will find commands, comments and system responses or other screen-displayed information involved in the configuration process.
- Page 7 Service profile commands (SSID & security policy setup) WPA2-PSK Assume you are creating service profile “vowlan-wpa2” to define the ESSID “phones,” as well as a WPA2-PSK security policy. The following commands are needed to setup the service for MP access points: set service-profile Voice ssid-name vowlan-wpa2 # sets the name of the service profile and SSID to...
- Page 8 # defines a passphrase set service-profile Voice auth-psk enable # enables pre-shared key authentication set service-profile Voice auth-dot1x disable # disables 802.1x authentication set service-profile Voice attr vlan-name default # maps the handsets to the vlan named default Radio profile commands Assume you are creating radio profile “voice”...
-
Page 9: Radio Configuration
Radio configuration During VIEW Certification, the MP access points were tested directly connected to a port on the MX (e.g. port 1). The following commands will configure a specific access point’s radio to support the voice service: set ap 1 radio 1 mode disable # if the radio is currently enabled. - Page 10 Subnet roaming configuration between multiple MX switches To set up subnet roaming between two switches, a mobility domain must be configured on both switches. Choose one of the switches to be the “seed” switch. The IP addresses used in mobility domain configuration must use the system IP address of each switch).
-
Page 11: Checking The Configuration
Checking the configuration Once the switch is configured, issue the following command at the command prompt to check the SVP settings: sh ap qos-stats The following information should be displayed (repeat the command to see changes): =========================== The switch and AP are now ready for use with SpectraLink Wireless Telephones. - Page 12 Configuration File (For Reference Only) The following configuration file was used during VIEW Certification testing. The configuration below includes all configuration attributes, including defaults. Use the command this detailed version. To only see non-default configuration values, use the command Note: All of the lines below are commands, except for those preceded by the # symbol, which denotes a comment.
- Page 13 set service-profile VoWLAN-WPA wep active-multicast- index 1 set service-profile VoWLAN-WPA wpa-ie disable set service-profile VoWLAN-WPA rsn-ie enable set service-profile VoWLAN-WPA cipher-tkip enable # for WPA this should be disabled set service-profile VoWLAN-WPA cipher-ccmp enable # for WPA this should be enabled set service-profile VoWLAN-WPA cipher-wep104 disable set service-profile VoWLAN-WPA cipher-wep40 disable set service-profile VoWLAN-WPA auth-dot1x disable...
- Page 14 Configuration Guide set radio-profile RealRadio auto-tune power-backoff- timer 10 set radio-profile RealRadio active-scan disable set radio-profile RealRadio qos-mode svp set radio-profile default 11g-only disable set radio-profile default beacon-interval 100 set radio-profile default dtim-interval 1 set radio-profile default max-tx-lifetime 2000 set radio-profile default max-rx-lifetime 2000 set radio-profile default rts-threshold 2346 set radio-profile default short-retry 5 set radio-profile default long-retry 5...
- Page 15 Trapeze Networks: Mobility System for MP 422 Access Points set ap 2 name MP02 set ap 2 bias high set ap 2 blink disable set ap 2 upgrade-firmware enable set ap 2 group none set ap 2 radio 1 channel 6 tx-power 2 radio-profile default mode disable set ap 2 radio 1 auto-tune max-power default min-client- rate 5.5 max-retransmissions 10...
- Page 16 set spantree uplinkfast disable set spantree fwddelay 15 vlan 1 set spantree hello 2 vlan 1 set spantree maxage 20 vlan 1 set spantree priority set spantree disable vlan 1 set igmp disable vlan 1 set igmp proxy-report enable vlan 1 set igmp querier disable vlan 1 set igmp mrsol disable vlan 1 set igmp version 2 vlan 1...