Advertisement
ACCESSORY INSTALLATION
MODEM COMMUNICATIONS continued
The TEC modem functions like any other modem. It can be called from a personal computer that has
it's own modem (either external or internal), and uses some form of terminal communications program,
or a CRT terminal connected to a modem.
I N STR U CTI O N S
PR E S S # T O FI N D N A M E AN D C O D E
PR E S S AN D H O L D # F O R F A S T FO R W A R D
PR E S S AN D H O L D * FO R FAS T R E V E R S E
EN T E R C O D E O N KEY P A D TO P L A C E C A L L
PR E S S # T O ST A RT O VE R
TEC
CAT
For computers equipped with Windows, the optional Selcom 7 or newer may be used to control the
TEC series unit. This program has many features, including automatic upload (sending information to
the TEC unit) and automatic download (getting information from the TEC unit).
COMPUTERS WITH OTHER TERMINAL PROGRAMS
If another terminal communications program is used, interactive control of the TEC is possible, but
uploading and downloading of information is not possible Uploading and downloading requires Selcom
7 or Newer. Set the terminal communications parameters to 8, N,1 and Vt-100 emulation, then call the
phone number attached to the TEC. The required dial out prefix for most Hayes™ compatible
modems should be ATE1V1S7=180DT and the phone number. If your software supports terminal
emulation, set it to VT-100B emulation. If it does not, program the TEC terminal type in Pg. 52 from VT
-100B to "dumb" terminal mode.
rings (this assumes the factory default of three rings has not been changed). After the modems begin
communicating, the message CONNECT XXXX will appear on the screen. If the message CONNECT
appears without being followed by XXXX, then the modem has dropped down to 300 baud. Either the
phone line signals are noisy or your personal computer modem may be capable of only 300 baud.
Next, this prompt will appear on the CRT screen of your personal computer:
PASSWORD
You have 10 seconds to begin entering the password. If you wait more than 10 seconds before
entering the password the TEC will revert back to normal operation and you will have to call the TEC
again.
All TEC systems leave SES with a factory password of 777777. As the password is entered,
the screen will replace each character with an "*" to keep the password confidential. After the
password is entered, the main menu will be displayed. If more than 60 seconds elapse without a
keystroke, the TEC will disconnect. It will then be necessary to call the TEC again. In order to prevent
unauthorized persons from accessing the TEC through a phone line the TEC will disconnect if any
keys are entered before the PASSWORD appears on the screen. To exit from programming, press the
"Esc" (escape) key. Due to the large number of communications programs, it is not possible for SES
to support any terminal communications programs except Selcom 7 or newer.
Page 22
PHONE
COMPAN Y
CENTRAL
OFFICE
When the personal computer calls the TEC, it will answer after 3
TEC Series v 3.2X
MODEM
PERSONAL
COMPUTER
Advertisement
Need help?
Do you have a question about the TEC Series and is the answer not in the manual?
Questions and answers
How to change a listed resident's phone number
To change a listed resident's phone number in the Select Engineered Systems TEC Series, you need the Manager's Password. The first three digits of the Program Password serve as the Manager's Password. Once you have access, follow these steps:
1. Enter the Communications Setup menu.
2. Use the Manager's Password to access the settings that allow phone number changes.
3. Locate the option to edit resident details, including phone numbers.
4. Input the new phone number.
5. Confirm the change by pressing the "Enter" key.
This updates the resident's phone number in the system.
This answer is automatically generated