Table of Contents
Advertisement
g
NOTE
The factory default IP address of the switch is 10.10.10.1. The factory default subnet mask is 255.255.255.0. If the switch is connected to a Dynamic Host
Control Protocol (DHCP) server, the server assigns the switch an IP address and the default 10.10.10.1 IP address is not configured. The DHCP server
also assigns your PC the correct IP address to allow a connection on the same subnet as the switch.
Initial Switch Configuration Procedure
To initially configure the switch, complete the following steps.
1. Power up the PC that you will use for the initial configuration. Please make sure the PC has the Ethernet RJ-45 connector to be connected to the
switch via standard Ethernet LAN cable. If the switch is connected to a DHCP server, skip to Step 3.
2. Reconfigure the PC's IP address and subnet mask as below, so that it can communicate with the switch. For example, the method to change the
PC's IP address for a PC running Windows® 7/8.x/10 is as follows:
a. Type network and sharing into the Search box in the Start Menu.
b. Select Network and Sharing Center.
c. Select Change adapter settings on the left of PC screen.
g
NOTE
Users can also skip Steps 1-2, by pressing WinKey+R and typing the ncpa.cpl command to get to Step 4 directly.
■
Right-click on your local adapter and select Properties.
■
In the Local Area Connection Properties menu, highlight Internet Protocol Version 4 (TCP/IPv4). Then, select the Properties button.
g
NOTE
Be sure to record all your PC's current IP settings to be able to restore them later.
■
Select the radio button Use the following IP address and enter in the IP address for the PC (e.g., any IP address not in use, and in between
10.10.10.2 and 10.10.10.254), subnet mask (e.g., 255.255.255.0).
■
Select OK to change the PC's IP address.
3. Power up the switch to be initially configured, and wait until it has finished its start-up processes.
4. Connect the PC to any port on the switch using a standard Ethernet cable, and check the port LED on the switch to make sure the link status of the
PC is OK.
5. Run your web browser on the PC; enter either the DHCP-assigned or factory default IP address to access the switch's web interface. If your PC is
configured correctly, you will see the login page of the switch requesting your username and password. In some browsers, the information needed
may be requested in a new window.
If you do not see the login page, perform the following steps:
a. Refresh the web page.
b. Check to see if there is an IP conflict issue.
c. Clean browser cookies and temporary Internet files.
d. Check your PC settings again and repeat Step 2.
6. Enter the factory default username in the login page. Select Login to log into the switch.
g
NOTE
The factory default username of the switch is admin. The factory default password is password.
Initial Switch Configuration Using CLI
The CLI can be accessed using any one of the two console ports (USB & RJ45) available in the switch. To establish the connection to the console port, the
following are needed:
■
PC with VT100 terminal emulation software
■
Micro USB to USB cable or a DB-9 to RJ45 Serial Cable (the cables are provided along with the unit)
g
NOTE
There are many terminal emulation applications available on the web. PuTTY, SecureCRT, and HyperTerminal are a few examples.
Complete the following steps:
1. Connect a Micro USB cable to the micro USB CONSOLE port or connect a DB-9 to RJ-45 serial cable to the RJ-45 CONSOLE port.
2. If using a Micro USB cable, connect the other end of the USB cable to a USB port on the PC. If using an RJ-45 serial cable, connect the other end
to the serial terminal on the PC.
3. If using the Micro USB cable to connect the switch, check if the USB drivers are automatically installed in the PC. If not install manually.
617108108PF2-13D
5
Advertisement
Table of Contents
