Table of Contents
Advertisement
NL
What to do in case of malfunctions?
3 What to do in case of malfunctions?
Malfunctions are often caused by a trifle. Before
What to do at jst or ingen?
contacting the after-sales service, try to rectify the fault
yourself using the table.
Fix faults yourself
You can often easily remedy technical faults on the
device yourself.
If a dish does not turn out optimally, you will find
many tips and instructions for preparation at the end
of the instructions for use. ~" Tested for you in our
cooking studio." on page 26
Possible
Malfunction
cause
Fuse
Device works
not.
defective.
Power Down
refraction
Power Down
On the display
the time flashes.
refraction.
Device cannot
Child lock is
activated.
be entered
suggested. The
display shows a
key symbol
lit or
'"".
Device-
The appliance door
can't be
door has been
latched with
opened. On the
display is a
the children's
key symbol
key lock.
lit.
Device-
The appliance door
can't be
door has been
locked by key symbol
opened. On the
display is a
the cleaning
key symbol
function.
h.
lit
The device Switch off the device, leave
After switching on
len of a function
has not yet cooled down completely and the function is
œ
flashes
on
switched off again in the process.
the display.
cooled.
The device
the demon-
stration mode the mains (fuse in the meter box has
does not heat up.Op
the display blinks
tripped)
spring. demonstration mode then
pert the double
point. at many
devices
š
also shines a
on the display.
- - - - - - - -
22
Solution / clue
Check the fuse in the
meter box.
Check whether the kitchen light or
other kitchen appliances are
working.
Reset the time.
Deactivate the child lock by
pressing the button with the key
symbol for approx. 4 seconds.
Deactivate the child lock by
pressing the button with the key
symbol for approx. 4 seconds.
The lock can be
deactivated in the basic
settings.
Wait until the cooking compartment has
cooled down and the
huh
has disappeared.
Disconnect the device from switching
off for a while) and deactivate the
within approx. 5 minutes, by setting
™‚„
™›
basic setting
or
on
s
the value
to put.
~" Basic settings"
on page 15
:
Warning – Risk of injury!
Improper repairs are dangerous. Never attempt to
repair the device yourself. Repairs should only be
performed by technicians instructed by customer
service. Contact the service department in the event of a
defect in the appliance;
:
Warning – Risk of electric shock!
Improper repairs are dangerous. Repairs and the
replacement of damaged connection cables may only be
carried out by technicians instructed by customer
service. If the device is defective, remove the plug from
the socket or switch off the fuse in the meter box.
Contact customer service.
Error messages on the display
When an error message with "
v.
touch the button
The
error message is then reset. If necessary, reset the time.
If it was a one-time malfunction, you can use the device
as usual. If the error message appears again, please
contact the after-sales service, stating the exact error
message and the E-No. from your device. ~" Customer
Service" on page 23
Maximum operating time
If you have not changed the settings of your appliance
for several hours, the heating will stop automatically.
This prevents the device from continuing to work
unintentionally.
The time at which the maximum operating time is
reached depends on the different device settings.
Maximum operating time reached
"‰.
The display shows
Turn the function selector knob to the zero position.
You can reset if necessary.
Tip:
You can set a duration to prevent the appliance
from switching off unintentionally, e.g. during very long
cooking times. The appliance heats up until the set time
has elapsed.
"
"‹†-„ƒ,
" appears, e.g.
Advertisement
Table of Contents
