Hameg HMC8012 Programmer's Manual page 5

SCPI Commands HMC8012
By default, the instrument is configured to use dynamic TCP/IP configuration and obtain all address information au-
tomatically. This means that it is safe to establish a physical connection to the LAN without any previous instrument
configuration.
Risk of network errors
Connection errors can affect the entire network. If your network does not support DHCP, or if you choose
to disable dynamic TCP/IP configuration, you must assign valid address information before connecting the
S C P I P r o g r a m m e r s M a n u a l instrument to the LAN. Contact your network administrator to obtain a valid IP address.
Configuring LAN parameters
S C P I P r o g r a m m e r s M a n u a l
S C P I P r o g r a m m e r s M a n u a l
1. Press the SETUP key and then the Interface softkey.
2. Press the Ethernet and then the Parameter softkey.
Note: By default, the instrument is set to not use DHCP. If the instrument is set to use DHCP and cannot find a DHCP
server, it takes about two minutes until the Ethernet menu is available.
The „Ethernet Settings" dialog box is displayed.
:ACQuire
Fig. 1.1: Ethernet Settings dialog box
:CHAN1OFFSet
Some data is displayed for information only and cannot be edited. This includes the „MAC" (physical) address of the
connector and the „Link" status information.
4. Define the IP address of the instrument by entering each of the four blocks individually (manual mode) or choose the
automatic IP-Mode.
a) In manual mode (MAN) define the first block number using the knob.
b) Press Next to move to the next block and define the number.
c) When the IP address is complete, press Down to continue with the next setting.
5. Define the „Subnetmask" and „Gateway" in the same way.
6. Select the „RAW Port" - the port number for SCPI socket communication.
7. Select the „VXI-11- Port" used by the instrument.
8. Select the „Transfer" mode. This mode can either be determined automatically („Auto" setting), or you can select a
combination of a transfer rate and half or full duplex manually.
9. Press Save to save the LAN parameters.
HAMEG Instruments GmbH • Industriestr. 6 • D-63533 Mainhausen • Deutschland
HAMEG Instruments GmbH • Industriestraße 6 • D-63533 Mainhausen
HAMEG Instruments GmbH • Industriestraße 6 • D-63533 Mainhausen
Tel.: +49 (0) 6182 800 0 • Fax: +49 (0) 6182 800 100 • E-Mail: info@hameg.com Tel.: +49 (0) 6182 800 0 • Fax: +49 (0) 6182 800 100 • E-Mail: info@hameg.com
Tel.: +49 (0) 6182 800 0 • Fax: +49 (0) 6182 800 100 • E-Mail: info@hameg.com
Geschäftsführer: Dipl.-Ing. Holger Asmussen, Dipl.-Ing. Andre Vander Stichelen • AG Offenbach am Main HRB 41200
Geschäftsführer: Dipl.-Ing. Holger Asmussen • AG Offenbach am Main HRB 41200
Geschäftsführer: Dipl.-Ing. Holger Asmussen • AG Offenbach am Main HRB 41200
:DISPlay
:HCOPy
*ESR?
H M O S e r i e s
H M S S e r i e s
H M S S e r i e s
Firmware Version: 01.020 and later
Firmware Version: 01.020 and later
Firmware Version: 03.00 and later
:MEASure
:LOGic:SIZE
*OPC?
HMO352x, HMO2524
HMO72x ... HMO202x
:POD1
:SYSTem
*SRE?
Subject to change without notice
Subject to change without notice
Subject to change without notice
English
English
English
5
1 1
1