Table of Contents
Advertisement
SCPI Commands HMC8012
Bit No. Meaning
0
Operation Complete
This bit is set on receipt of the command *OPC exactly, when all previous commands have been
executed.
1
Not used
2
Query Error
This bit is set, if either the controller wants to read data from the instrument without having sent a
S C P I P r o g r a m m e r s M a n u a l
query, or if it does not fetch requested data and sends new instructions to the instrument instead.
The cause is often a query which is faulty and hence cannot be executed.
3
Device-dependent Error
This bit is set, if a device-dependent error occurs. An error message with a number between -300
S C P I P r o g r a m m e r s M a n u a l
and -399 or a positive error number is entered into the error queue.
S C P I P r o g r a m m e r s M a n u a l
4
Execution Error
This bit is set if a received command is syntactically correct, but cannot be performed for other rea-
sons. An error message with a number between -200 and -300 is entered into the error queue.
5
Command Error
This bit is set, if a command is received, which is undefined or syntactically incorrect. An error mes-
sage with a number between -100 and -200 is entered into the error queue.
6
Not used
7
Power On (supply voltage on)
This bit is set, when switching on the instrument.
Table 1.9: Bits of the event status register (please refer to page 20)
STATus:OPERation Register
In the CONDition part, the register contains information which operations the instrument is being executing. In the
EVENt part, it contains information which operations the instrument has executed since the last reading. It can be read
using the commands STATus:OPERation:CONDition? or STATus:OPERation[:EVENt]?.
The remote commands for the STATus:OPERation register are described on page 65.
Bit No.
0
:ACQuire
1 to 3
:CHAN1OFFSet
4
5
6 to 9
10
11 to 15
Table 1.10: Bits of the STATus:OPERation register (please refer to page 20)
HAMEG Instruments GmbH • Industriestr. 6 • D-63533 Mainhausen • Deutschland
HAMEG Instruments GmbH • Industriestraße 6 • D-63533 Mainhausen
HAMEG Instruments GmbH • Industriestraße 6 • D-63533 Mainhausen
Tel.: +49 (0) 6182 800 0 • Fax: +49 (0) 6182 800 100 • E-Mail: info@hameg.com
Tel.: +49 (0) 6182 800 0 • Fax: +49 (0) 6182 800 100 • E-Mail: info@hameg.com
Tel.: +49 (0) 6182 800 0 • Fax: +49 (0) 6182 800 100 • E-Mail: info@hameg.com
Geschäftsführer: Dipl.-Ing. Holger Asmussen, Dipl.-Ing. Andre Vander Stichelen • AG Offenbach am Main HRB 41200
Geschäftsführer: Dipl.-Ing. Holger Asmussen • AG Offenbach am Main HRB 41200
Geschäftsführer: Dipl.-Ing. Holger Asmussen • AG Offenbach am Main HRB 41200
Meaning
Calibrating
(for service department only)
Not used
Measuring
The bit is set, while the instrument is measuring.
Waiting for Trig
:DISPlay
This bit is set while the instrument is waiting for the trigger.
Not used
Instrument Locked (RWLock)
Not used
:HCOPy
*ESR?
H M O S e r i e s
H M S S e r i e s
H M S S e r i e s
Firmware Version: 01.020 and later
Firmware Version: 01.020 and later
Firmware Version: 03.00 and later
:MEASure
:LOGic:SIZE
*OPC?
HMO352x, HMO2524
HMO72x ... HMO202x
:POD1
:SYSTem
*SRE?
Subject to change without notice
Subject to change without notice
Subject to change without notice
English
English
English
17
1
1
1
Advertisement
Chapters
Table of Contents
