Hameg HMC8012 Programmer's Manual page 23

SCPI Commands HMC8012
*TST?
self TeST query
Triggers selftests of the instrument and returns an error code in decimal form (see Service Manual supplied with the
instrument). „0" indicates no errors occured.
Usage:
S C P I P r o g r a m m e r s M a n u a l
*WAI
WAIt to continue
S C P I P r o g r a m m e r s M a n u a l
S C P I P r o g r a m m e r s M a n u a l
Prevents servicing of the subsequent commands until all preceding commands have been executed and all signals
have settled (see also command synchronization and *OPC).
Usage:
2.2 System related commands
FETCh? ....................................................................................................................... 23
READ? ........................................................................................................................ 23
SYSTem:BEEPer:STATe <State> ............................................................................... 24
SYSTem:BEEPer:STATe? ............................................................................................ 24
SYSTem:BEEPer[:IMMediate] .................................................................................... 24
SYSTem:ERRor[:NEXT]? ............................................................................................ 24
SYSTem:LOCal ........................................................................................................... 24
SYSTem:REMote ....................................................................................................... 24
SYSTem:RWLock ....................................................................................................... 24
SYSTem:VERSion? ..................................................................................................... 24
FETCh?
:ACQuire
Query the actual measurement value on the display in auto trigger, single trigger or manual trigger mode. In contrast
to the READ? command the FETC? command does not initialize a trigger. By sending the *TRG command before the
:CHAN1OFFSet
FETC? command you get the actual triggered measurement value.
Usage:
READ?
Query the actual measurement value in auto trigger mode. In the single trigger mode the READ? command initialize
a trigger with the settings for trigger count or interval. In the trigger manual mode the READ? command initialize a
trigger. By sending the READ? command again the trigger mode stops. Please notice that the READ? command only
queries the first measurement value of the trigger system.
Usage:
HAMEG Instruments GmbH • Industriestr. 6 • D-63533 Mainhausen • Deutschland
HAMEG Instruments GmbH • Industriestraße 6 • D-63533 Mainhausen
HAMEG Instruments GmbH • Industriestraße 6 • D-63533 Mainhausen
Tel.: +49 (0) 6182 800 0 • Fax: +49 (0) 6182 800 100 • E-Mail: info@hameg.com Tel.: +49 (0) 6182 800 0 • Fax: +49 (0) 6182 800 100 • E-Mail: info@hameg.com
Tel.: +49 (0) 6182 800 0 • Fax: +49 (0) 6182 800 100 • E-Mail: info@hameg.com
Geschäftsführer: Dipl.-Ing. Holger Asmussen, Dipl.-Ing. Andre Vander Stichelen • AG Offenbach am Main HRB 41200
Geschäftsführer: Dipl.-Ing. Holger Asmussen • AG Offenbach am Main HRB 41200
Geschäftsführer: Dipl.-Ing. Holger Asmussen • AG Offenbach am Main HRB 41200
Query only
Event
Query only
:DISPlay
:HCOPy
Query only
*ESR?
H M O S e r i e s
H M S S e r i e s
H M S S e r i e s
Firmware Version: 01.020 and later
Firmware Version: 01.020 and later
Firmware Version: 03.00 and later
:MEASure
:LOGic:SIZE
*OPC?
HMO352x, HMO2524
HMO72x ... HMO202x
:POD1
:SYSTem
*SRE?
Subject to change without notice
Subject to change without notice
Subject to change without notice
English
English
English
23
1 1
1