Hameg HMC8012 Programmer's Manual page 22

SCPI Commands HMC8012
*IDN?
IDeNtification: returns the instrument identification.
Return values:
<ID>
Example:
S C P I P r o g r a m m e r s M a n u a l
Usage:
S C P I P r o g r a m m e r s M a n u a l
S C P I P r o g r a m m e r s M a n u a l
*OPC
OPeration Complete
Sets bit 0 in the event status register when all preceding commands have been executed. This bit can be used to ini-
tiate a service request. The query *OPC? writes a „1" into the output buffer as soon as all preceding commands have
been executed. This is used for command synchronization.
*RST
ReSeT
Sets the instrument to a defined default status. The default settings are indicated in the description of commands.
Usage:
*SRE <Contents>
Service Request Enable
Sets the service request enable register to the indicated value. This command determines under which conditions a
service request is triggered. The query *SRE? returns a decimal value of the Status Byte enable register which corre-
sponds to the binary-weighted sum of all bits.
Parameters:
:ACQuire
<Contents>
:CHAN1OFFSet
Range:
*STB?
STatus Byte query
Returns the contents of the status byte in decimal form.
Usage:
*TRG
TRiGger
Triggers all actions waiting for a trigger event. In particular, *TRG generates a manual trigger signal (Manual Trigger).
This common command complements the commands of the TRIGger subsystem.
Usage:
HAMEG Instruments GmbH • Industriestr. 6 • D-63533 Mainhausen • Deutschland
HAMEG Instruments GmbH • Industriestraße 6 • D-63533 Mainhausen
HAMEG Instruments GmbH • Industriestraße 6 • D-63533 Mainhausen
Tel.: +49 (0) 6182 800 0 • Fax: +49 (0) 6182 800 100 • E-Mail: info@hameg.com Tel.: +49 (0) 6182 800 0 • Fax: +49 (0) 6182 800 100 • E-Mail: info@hameg.com
Tel.: +49 (0) 6182 800 0 • Fax: +49 (0) 6182 800 100 • E-Mail: info@hameg.com
Geschäftsführer: Dipl.-Ing. Holger Asmussen, Dipl.-Ing. Andre Vander Stichelen • AG Offenbach am Main HRB 41200
Geschäftsführer: Dipl.-Ing. Holger Asmussen • AG Offenbach am Main HRB 41200
Geschäftsführer: Dipl.-Ing. Holger Asmussen • AG Offenbach am Main HRB 41200
HAMEG,‹device type›,‹serial number›,‹firmwareversion›
HAMEG,HMC8012,12345,01.000
Query only
Setting only
Contents of the service request enable register in decimal form.
Bit 6 (MSS mask bit) is always 0.
0 to 255
:DISPlay
:HCOPy
Query only
*ESR?
Event
H M O S e r i e s
H M S S e r i e s
H M S S e r i e s
Firmware Version: 01.020 and later
Firmware Version: 01.020 and later
Firmware Version: 03.00 and later
:MEASure
:LOGic:SIZE
*OPC?
HMO352x, HMO2524
HMO72x ... HMO202x
:POD1
:SYSTem
*SRE?
Subject to change without notice
Subject to change without notice
Subject to change without notice
English
English
English
22
1 1
1