Register Table - Bender ISOMETER iso415R Manual

Modbus settings
5.2

Register table

Address Register name
(dec)
Device information (0...99)
0 Device name
16 Article number
32 Serial number
48 Manufacturer
64 Application D number
65 Application version number
66 Application build number
67 Boot loader D number
68 Bootloader version number
69 Boot loader build number
70 Device status
Alarm and measured values (999...1999)
999 Number of active alarms
1000 Insulation resistance R
1001 Alarm-1
1002 Alarm-2
1003 Measuring range status R
Monitoring functions (2000...2999)
2000 Alarm-E/KE
2001 Alarm-L1/L2
2002 R_EKE
2003 R_L1L2
Status information (3000...3999)
3000 Test status
3001 Insulation fault location
3002 Measured value
update counter
22 iso415R-x_D00401_00_M_XXEN / 04.2021
Data type Bytes Mode
String UTF8 32
String UTF8 32
String UTF8 32
String UTF8 32
Uint16 2
Uint16 2
Uint16 2
Uint16 2
Uint16 2
Uint16 2
Uint16 2
Uint16 2
Uint16 2
F
Uint16 2
Uint16 2
Uint 16 2
F
Uint16 2
Uint 16 2
Uint16 2
Uint16 2
Uint16 2
Int16 2
Uint32 4
Value/Unit/Comment
RO iso415R-24 or iso415R-2
RO B71602000 (iso415R-24)
B71603000 (iso415R-2)
RO 10 digits e.g.: 2002123456
RO Bender
RO 704 = D704
RO xxx = Vx.xx
RO
RO 705 = D705
RO xxx = Vx.xx
RO
RO Bit 0 (LSB): NFC - 0 = disabled, 1 = enabled
Bit 1: Potentiometer R
Bit 2: Potentiometer R
Bit 3-15: 0 (reserved)
RO 0...7
RO 0...10000 [kΩ]
RO 0 = No alarm
2 = Alarm, measured value below Ran1
RO 0 = No alarm
2 = Alarm, measured value below Ran2
RO 0 = " " within measuring range 1 kΩ...10 MΩ
1 = "<" below measuring range
2 = ">" measuring range exceeded
RO 0 = No alarm
2 = Alarm, E/KE connection faulty
RO 0 = No alarm
2 = Alarm, L1/L2 coupling faulty
RO 0...1000 [kΩ];
Resistance between terminals E and KE
RO 0...1000 [kΩ];
Resistance between terminals L1 and L2
RO 0 = No active test
1 = Internal test (local)
2 = External test (remote)
RO 0 = Insulation fault cannot be located
100 = Insulation fault mainly at L1(+)
-100 = Insulation fault mainly at L2(-)
RO 0...2 32
- 0 != ext, 1 = ext
an1
- 0 != ext, 1 = ext
an2
Factory
setting
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A