Related Manuals for Jetter JC-24x
Summary of Contents for Jetter JC-24x
- Page 1 JC-24x Version Update from V 3.25 to V 3.26 Revision 1.01 December 2008 / Printed in Germany...
- Page 2 Introduction Revision 1.01 Jetter AG reserves the right to make alterations to its products in the interest of technical progress. These alterations need not be documented in every single case. This User Manual and the information contained herein have been compiled with due diligence. However, Jetter AG assume no liability for printing or other errors or damages arising from such errors.
-
Page 3: Table Of Contents
JC-24x - Version Update from 3.25 to 3.26 Contents Table of Contents Introduction Operating System Update......................5 Overview of Version Updates......................6 New Features Festo CPX-CP Interface.......................8 Restrictions at Using the CAN System Bus ...................9 Access to the Modules at the CPX-CP Interface .................10 Fixed Software Bugs N_COPY_TO/FROM(2) with more than 64 registers in mode 2..........13... -
Page 4: Introduction
1 Introduction Introduction Introduction This chapter shows the history of OS versions for the controller JC-24x. An OS update for the controller JC-24x allows you to: Operating System Update - Why? add new functions to your controller fix software bugs... -
Page 5: Operating System Update
OS file for JC-24x with version 3.26 Downloading the OS File Jetter AG make operating system files available for download from their homepage at www.jetter.de. OS files can be found in the support area or on the page of the JC-24x controller via quicklink. Operating System... -
Page 6: Overview Of Version Updates
OS version 3.26: Feature Festo CPX Terminal: Support for CPX-CPI interface N_COPY_TO/FROM(2) More than 64 registers in copy mode 2 BWU1821: Communication via command interface Read and write access to analog IOs LioN-S: Commissioning Register access Jetter AG... -
Page 7: New Features
New Features Introduction Jetter AG are continuously striving to add new features and functions to the controller JC-24x. By updating your OS you are given the possibility to enhance the functionality of your controller. To do so, you need the following ... -
Page 8: 2.1 Festo Cpx-Cp Interface
Required Hardware and The following hardware and operating system versions are required for Operating System applying the CPX-CPI interfaces to Jetter AG controllers: Versions Module Comment As of Software... -
Page 9: Restrictions At Using The Can System Bus
JC-24x - Version Update from 3.25 to 3.26 New Features Restrictions at Using the CAN System Bus Restrictions at Using the The usage of the CPX-CP interface at the CPX-FB14 is subject to the following restrictions: CPX-CP Interface The required hardware and operating system versions have to be kept to. -
Page 10: Access To The Modules At The Cpx-Cp Interface
I/O Numbers of JC-647 The I/Os at the JC-647 connected with the JX6-SB(-I) submodule are numbered in analogy with the I/O numbering at the JC-24x. The input and output numbers have just got to be prefixed. The prefix corresponds to the submodule slot number + 1. - Page 11 JC-24x - Version Update from 3.25 to 3.26 New Features the I/Os at the CPI strings 3 and 4 are represented by the next but one I/O module number The numbers of the additionally occuppied I/O modules are entered into the...
-
Page 12: Fixed Software Bugs
N_COPY_TO/FROM(2) with more than 64 registers in mode 2....13 Writing Commands to the BWU1821............14 Reading and Writing Analog I/Os at the BWU1821 ........15 Initializing by means of LioN-S Modules............16 Register Access to LioN-S Modules ............. 17 Jetter AG... -
Page 13: N_Copy_To/From(2) With More Than 64 Registers In Mode 2
JC-24x - Version Update from 3.25 to 3.26 Fixed Software Bugs N_COPY_TO/FROM(2) with more than 64 registers in mode 2 Effects of this Bug If ... more than 64 register values are sent to another controller or retrieved from it using... -
Page 14: Writing Commands To The Bwu1821
Writing Commands to the BWU1821 BWU1821 The BWU1821 is a gateway between AS interface and CANopen of the Bihl+Wiedemann GmbH. It can be directly connected to the Jetter CAN system bus. Commands of a length greater than 4 bytes cannot be transmitted to the Effects of this Bug BWU1821. -
Page 15: Reading And Writing Analog I/Os At The Bwu1821
Reading and Writing Analog I/Os at the BWU1821 BWU1821 The BWU1821 is a gateway between AS interface and CANopen of the Bihl+Wiedemann GmbH. It can be directly connected to the Jetter CAN system bus. Reading and writing of AS interface slaves by means of analog inputs and Effects of this Bug outputs renders wrong results. -
Page 16: Initializing By Means Of Lion-S Modules
In case of CAN system bus configurations consisting of LioN-S and JX2-/JX3 modules, not all connected JX2-/JX3 modules are commissioned. Affected Revisions The following revisions are affected by this bug: OS revision JX6-SB(-I) < 2.21.0.00 JC-24x < 3.26.0.00 JM-D203-JC24x < 1.13.0.00 Hardware revision not relevant Configuration or operating mode... -
Page 17: Register Access To Lion-S Modules
JC-24x - Version Update from 3.25 to 3.26 Fixed Software Bugs Register Access to LioN-S Modules Effects of this Bug Read or write access with LioN-S modules is not possible. Affected Revisions The following revisions are affected by this bug:...
Need help?
Do you have a question about the JC-24x and is the answer not in the manual?
Questions and answers