Optional Settings; Operation Check; Led Indication - Optex Smart Line Series Installation Instructions Manual

4-3 OPTIONAL SETTINGS

BEAM INTERRUPTION ADJUSTMENT
1
Initial setting is at 50 ms for normal work. According to the speed of
a supposed target you select one specific setting out of 4 steps.
Set the beam interruption adjustment switches of the Receiver
according to the speed of the human object to detect.
ON
SELECTOR
POSITION
SL-350QFR
SL-350QNR
Running Jogging
(50 msec) (100 msec)
Typical
interruption
time setting
BATTERY SAVING TIMER
2
Alarm output activation is limited to 2 minutes by a timer.
Even if there are continuous alarm events, the alarm output
operates only once in the timer period.
Receiver Transmitter
ON
OFF • Alarm output: 1 output/ 2 minute
SL-350QFR • D.Q. output: 1 output/ 2 minute
• Low battery output: 1 output/ 15 minutes
SL-350QNR
• Remove all batteries prior to replacing with new
ones. If this is not followed, the low battery indicator
LED will not reset and continue to blink.
INTERMITTENT OUTPUT FUNCTION
3
When wireless configuration is being used, which is unable to
determine whether the alarm output continues, setting the
intermittent output function to the "ON" position, turns on the
intermittent alarm output. This configures the wireless transmitter
to send alarms at a specific time intervals.
Receiver Transmitter
ON
• Alarm output: 1 output/ 1 minute
OFF
• D.Q. output: 1 output/ 1 minute
SL-350QFR
• Low battery output: 1 output/ 5 minutes
SL-350QNR
D.Q. OUTPUT
4
(ENVIRONMENTAL DISQUALIFICATION)
D.Q. will send a trouble signal when the beam strength is below
acceptable levels, for more than 20 seconds, due to rain, snow, or
heavy fog.
< Operating Time Chart >
Reception level
Adverse weather
Alarm output level
D.Q. output
< Wiring example >
D.Q. and ALARM are output separately.
Receiver
DQ
ALARM
NO NC COM COM NC NO
Input Input
(N.C.) (N.C.)
Wireless transmitter
Walking Slow movement
(250 msec) (500 msec)
Caution
2 sec.
20 sec.
level
ON
OFF
Canceling ALARM output in adverse
weather conditions
Receiver
DQ ALARM
NO NC COM COM NC NO
Input Input
(N.C.) (N.C.)
Wireless transmitter
EN-10
• This circuit sets N.O. for a low battery output,
whereas N.C. for an alarm. Be sure to use N.O.
ready wireless transmitter for this configuration.
Turn "OFF" both battery saving timer and
intermittent output function switches when applying
this wiring example.
5

OPERATION CHECK

5-1 LED INDICATION

Receiver
Alarm
Level-ind
Low Battery
Detection
(beam interruption)
ALARM
ON
(Receiver)
POWER
ON
(Transmitter)
LOW BATTERY
(Receiver&Transmitter)
5-2 OPERATION CHECK
After installation is complete, be sure to check the operation.
1
See "4-3 2 BATTERY SAVING TIMER" to turn OFF the
battery saving mode.
2 Make sure that the alarm indicator is off.
If it is illuminated even when the beams are not blocked,
make optical alignment again.
Receiver
Alarm
Level-ind
Low Battery
3
Check that the low battery indicator LEDs on both
transmitter and receiver are OFF.
If the indicator LED is blinking, the battery power is low.
Replace with the new batteries.
4
Conduct a walk test to check that Alarm indicator LED on
the receiver turns ON as the walker interrupts the beams.
Transmitter Receiver
A B
C
• For battery power savings, perform the operation
check before checking the following items.
(1) When installing on a wall or pole, make sure the
cover is properly attached to main unit.
(2) When installing in a beam tower, make sure the
tamper bushing is properly attached to main unit.
(See page 6 "Caution".)
Caution
Transmitter
Power
Low Battery
Low battery
Normal
power
OFF
ON
Blink
Be sure to conduct a walk test
at the following three points:
A. In front of the transmitter
B. In front of the receiver
C. At the mid point between the
transmitter and receiver
The detector is installed
properly when Alarm indicator
LED turns ON in the tests at all
the three points.
Caution