Mounting of the pellet burner Components of the swiveling arm Ceramics Ceramics replacement Air damper Benchmarks for heating with wood Benchmarks for heating with pellets Type plate Effecta AB - Västra Rågdalsvägen 21 - 434 99 Kungsbacka - 0300 - 22320 - info@effecta.se...
If the boiler is used to burn materials for which is not certified by the EPA If the boiler is not operated according to the owners manual. System data ▀ Date; Installer: Manufacturing number: Electrical installer Effecta AB - Västra Rågdalsvägen 21 - 434 99 Kungsbacka - 0300 - 22320 - info@effecta.se...
Disassmbly and disposal It will be many years before your Effecta boiler is worn out, but it is important that you follow the regulations in force at the time concerning disassembly and disposal of your boiler The fuel It is important to use the right kind of wood in your boiler.
Try to keep the following things in mind. The fuel Effecta Smart is tested to be fired with wood logs. What kind of wood has no greater effect to the boilers operation, except that hardwood has a greater calorific value than softwood. The result of using hardwood is that the accumulator is heated quicker with hardwood in compari- son to softwood.
To the installer ▀ It is time to install your Effecta Smart. Try to follow our instructions for a safe installation. After installation, be sure to instruct the customer on how the heating system and the boiler work, in order to avoid unnecessary complications in the future...
For the installation of the shunt automatic system, please follow the supplied description. Effecta AB - Västra Rågdalsvägen 21 - 434 99 Kungsbacka - 0300 - 22320 - info@effecta.se...
Page 9
This can sometimes lead to a high back pressure during new firing, since the chimney is cold. This is prevented with a draft stabiliser. (Read pg 31.) Effecta AB - Västra Rågdalsvägen 21 - 434 99 Kungsbacka - 0300 - 22320 - info@effecta.se...
Pipe for sensor Handle loading compart. door Cooling coil Loading compartment door Connecting box Control panel Over heat protection Start jug wheel Lambda probe Effecta AB - Västra Rågdalsvägen 21 - 434 99 Kungsbacka - 0300 - 22320 - info@effecta.se...
For more information and installation of the quench valve read the manufacterers documenta- tion. References above are products of Somatherm AB. It may differ between different brands. Effecta AB - Västra Rågdalsvägen 21 - 434 99 Kungsbacka - 0300 - 22320 - info@effecta.se...
Damper motor primary Orange Damper motor secondary Brown Damper motor primary Brown Power to board Zero 115 VAC Power to board Phase 115 VAC Effecta AB - Västra Rågdalsvägen 21 - 434 99 Kungsbacka - 0300 - 22320 - info@effecta.se...
Page 13
Room sensor shunt group 3 (1) Room sensor shunt group 3 (2) Room sensor shunt group 3 (3) Pot fri - Pot fr + Effecta AB - Västra Rågdalsvägen 21 - 434 99 Kungsbacka - 0300 - 22320 - info@effecta.se...
When connection the board use the conduits on the right side of the boiler (5). Remember to separate high voltage from low voltage. Effecta AB - Västra Rågdalsvägen 21 - 434 99 Kungsbacka - 0300 - 22320 - info@effecta.se...
Connect to 17 and 18 on the motherboard. The sensor G4 is mounted on the flow in order to sense requested loading tempera- ture. Effecta AB - Västra Rågdalsvägen 21 - 434 99 Kungsbacka - 0300 - 22320 - info@effecta.se...
(10) if the pressure is too high. Make sure that the drain pipe have runoff to a floor drain. Temperature adjustment Closing/Check valve Hot water Mixing valve Cold water Manifold Hot water out Safety valve Cold water in Drain pipe Effecta AB - Västra Rågdalsvägen 21 - 434 99 Kungsbacka - 0300 - 22320 - info@effecta.se...
Shunt control ▀ Effecta Smart has its own shunt control. The shunt control menu is activated when sensor G7 is connected. There you regulate the heating of your house. Start by choosing which sensor to control with, room sensor, out door sensor or both. If both are chosen the heat is controlled by the outdoor sensor but the room sensor can provide corrections on the supply temperature +/- 10°F, max room temp.
Adjustment 0 means that the flow is 68 °F at an outdoor temperature of 68°F. Adjustment -10 means that flow temperature is instead 58°F. Effecta AB - Västra Rågdalsvägen 21 - 434 99 Kungsbacka - 0300 - 22320 - info@effecta.se...
If it is warm outdoors (average autumn/spring) and the indoor temperature is too high. Decrease the adjustment with 2-4˚F. Wait at least 24 hours between adjustments and changes due to slow response of heating. Effecta AB - Västra Rågdalsvägen 21 - 434 99 Kungsbacka - 0300 - 22320 - info@effecta.se...
Wait until the picture of flags comes up on the display. Disconnect the USB-memory. Your boiler is now updated. Effecta AB - Västra Rågdalsvägen 21 - 434 99 Kungsbacka - 0300 - 22320 - info@effecta.se...
Temperature log for the boiler temperature. Temperature log for the loading temperatureladdningstem. NOTE! The log requires that the sensor is connected or function activated. Effecta AB - Västra Rågdalsvägen 21 - 434 99 Kungsbacka - 0300 - 22320 - info@effecta.se...
Page 24
Room sensor activated but the flow sensor(G7) is not connected. Alarm Outdoor sensor activated but not connected. Outdoor temp. Outdoor sensor activated but the flow sensor(G7) is not connected. Effecta AB - Västra Rågdalsvägen 21 - 434 99 Kungsbacka - 0300 - 22320 - info@effecta.se...
212 °F , or just above. Then open the upper door carefully to release any smoke from the loading compartment if necessary. Then put logs into the loading compartment and close the door. Effecta AB - Västra Rågdalsvägen 21 - 434 99 Kungsbacka - 0300 - 22320 - info@effecta.se...
Remember to slide the after burner chamber all the way in after cleaning. Effecta AB - Västra Rågdalsvägen 21 - 434 99 Kungsbacka - 0300 - 22320 - info@effecta.se...
Page 27
The old one is pulled out from the door, and the new one is pushed into place where the old one was positioned. Effecta AB - Västra Rågdalsvägen 21 - 434 99 Kungsbacka - 0300 - 22320 - info@effecta.se...
If your boiler is not equiped with door cleaning you lift out the turbulators one at a time and clean the tubes with the brush and brush off the turbulators. Effecta AB - Västra Rågdalsvägen 21 - 434 99 Kungsbacka - 0300 - 22320 - info@effecta.se...
Rotate the door ▀ As standard Effecta Smart is delivered with door hinges on the right side. If you need to replace the door hanging follow instructions below. Upper door 1. Start by loosening the two M12 bolts that hold the hatch against the frame. Remember to have a shelter over the hatch to avoid scratches in the paint with continued work.
The menus In Effecta Smart there is a menu selection for use of pellets(pg.22) YES/NO, before the burner starts choose YES. In the menu you need to set the temperatures for the burner to start and stop.
Mounting bolts heat shield M8 Insulation for heat shield Cover for heat shield Bracket for mounting arm Swiveling arm from boiler Swiveling arm for pellet burner Effecta AB - Västra Rågdalsvägen 21 - 434 99 Kungsbacka - 0300 - 22320 - info@effecta.se...
Grate stick Top left Spacer top Top right Distribution plate secondary air Distribution plate secondary air Bottom left Spacer bottom Bottom right Afterburner chamber Effecta AB - Västra Rågdalsvägen 21 - 434 99 Kungsbacka - 0300 - 22320 - info@effecta.se...
Damper motor Set screw Stop pin Motor shaft Air damper Bracket motor Distance Air box Spring Effecta AB - Västra Rågdalsvägen 21 - 434 99 Kungsbacka - 0300 - 22320 - info@effecta.se...
Values Unit Benchmark 9-11 mg /m³ (ppm) <200-400 Flue gas temperature °F 285-360 Vaccum in the chimney 15-20 Combustion efficiency 90-92 Type plate ▀ Effecta AB - Västra Rågdalsvägen 21 - 434 99 Kungsbacka - 0300 - 22320 - info@effecta.se...