Preventative Maintenance Table; Assembly - Snorkel SL26 Series Parts And Service Manual

PREVENTATIVE MAINTENANCE TABLE

INTERVAL
Daily = each shift or everyday
50 hrs/30 d = every 50 hours or 30 days
250 hrs/6 m = every 250 hours or 6 months
1000 hrs/2 y = every 1000 hours or 2 years
Y = Yes/Acceptable
N = No/Not Acceptable
R = Repaired/Acceptable
DO NOT fit replacement parts other than genuine components without express written approval
from the manufacturer.
COMPONENT INSPECTION OR SERVICES
Check electrolyte level
Check specific gravity
Battery
Clean exterior
System
Check battery cable condition
Clean terminals
Check level and condition
Engine Oil
Check for leaks
Change oil filter
Check fuel level
Engine
Check for leaks
Fuel system
Replace fuel filter
Check air cleaner
Engine Check coolant level
Coolant (with engine cold)
Replace coolant
Check oil level
Hydraulic Oil
Change filter
Drain and replace oil
Check for leaks
Hydraulic
Check hose connections
system
Check hoses for exterior wear
Emergency Operate the emergency lowering valve and
hydraulic check for serviceability
System
Controller Check switch operation
Control Cable Check the exterior of the cable for pinching,
binding or wear
Check fasteners for proper torque
Platform deck
Check welds for cracks
and rails
Check condition of deck
Check for damage
Tyres
Check lug nuts (torque to 122 Nm/90 ft. lbs.)
Wipe clean
Hydraulic
Check for leaks at mating surfaces
pump
Check for hose fitting leaks
Check mounting bolts for proper torque
Check for and repair collision damage
Entire
Check fasteners for proper torque
unit
Check for corrosion-remove and paint
Lubricate
Table 3-1: Preventative maintenance checklist
A thorough investigation should be carried out every 6 months.
NOTE: Frequency and extent of periodic examinations may depend on national regulations.
Fitment of any component other than approved items designed for use with this machine can result
in serious danger to operators, property and bystanders.
SL26/30SL
PREVENTATIVE MAINTENANCE REPORT
Date:
Owner:
Model #:
Serial #:
Serviced By:
Service Interval:
INTERVAL Y N R COMPONENT
Daily Drive Motors
6m
6m
Daily
6m
Daily
Daily
30d
Daily
Daily
6m
Daily
Daily
3m
Daily
6m
2y
Daily
30d
30d
Lift Cylinder
Daily
Daily
Daily
Fore/Aft cylinder &
Daily
side/side cylinder
Daily
Daily
Daily
30d
30d
30d
Daily
30d
Daily
3m
6m
Wheel bearings
30d
SERVICE AND REPAIR
INSPECTION OR SERVICES
Check for operation and leaks
Check hardware & fittings for proper
Steering torque
system
Grease pivot pins
Oil king pins
Check steering cylinder for leaks
Inspect for structural cracks
Check pivot points for wear
Check mounting pin pivot bolts for
Elevating
proper torque

Assembly

Check linkage gear for wear
Check elevating arms for bending
Grease linkage pins
Grease linkage gear
Check hoses for pinch or rubbing
Chassis points
Check component mounting for
proper torque
Check welds for cracks
Check the cylinder rod for wear
Check mounting pin pivot bolts for
proper torque
Check seals for leaks
Inspect pivot points for wear
Check fittings for proper torque
Check the cylinder rod for wear
Check mounting pin pivot bolts for
proper torque
Check seals for leaks
Inspect pivot points for wear
Check fittings for proper torque
Check the cylinder rod for wear
Check mounting pin pivot bolts for
Axle
proper torque
cylinder
Check seals for leaks
Inspect pivot points for wear
Check fittings for proper torque
Labels Check for peeling, missing or unread-
able labels & replace
Replace wheel bearings (replace
wheel bearings and seals at 2000
hours)
INTERVAL Y N R
Daily
6m
30d
30d
30d
Daily
30d
30d
6m
6m
30d
30d
Daily
6m
Daily
30d
30d
30d
30d
30d
30d
30d
30d
30d
30d
30d
30d
30d
30d
30d
Daily
2y
Page 3 - 3