Specifications - SMC Networks ZSE50F Manual

Specifications

Rated pressure range
Operating pressure range and regulating pressure range
Proof pressure
Note 1)
Setting/Display
resolution
Fluid
Power supply voltage
Current consumption
Switch output
Repeatability
Hysteresis mode
Hysteresis
Window comparator mode
Response time
Output short circuit protection
Display
Display accuracy
Indication light
Note 2)
Analog output
Note 3)
Auto shift input
Enclosure
Ambient temperature range
Ambient humidity range
Environmental
Withstand voltage
resistance
Insulation resistance
Vibration resistance
Shock resistance
Temperature characteristics
Wetted material
Port size
Lead wire
Weight
Note 1)
In case of types with unit conversion function. (Types without unit
conversion function are fixed to the SI units (KPa or MPa).)
Note 2)
When a type with analog output is selected.
Note 3) When a type with auto shift is selected.
Note 4) 0.03 to 0.04 psi in psi display.
Note 5) Value clear 0.01psi in psi display.
Function
Various additional functions are available for easy measurement, switch operation and check of measured values suitable for the
conditions of the measured fluid.
Note 1)
Auto shift function
Anti-chattering function
Key lock function
Peak hold function
Bottom hold function
Zero out function
Unit conversion (for overseas use)
Note 1) Select and order by specifying the types and models.
For General Fluids
High Precision Digital Pressure Switch
ZSE50F (Compound pressure)
kPa
MPa
kgf/cm 2
bar
psi
mmHg
inHg
NPN or PNP 2 output (Max. applied voltage 30V (NPN), Max. load current 80mA)
0.2% F.S.
2.5ms or less (with chattering prevention function: 24ms, 192ms, 768ms or less)
Green LED (OUT1: Light up when ON), Red LED (OUT2: Lights up when ON)
Output voltage: 1 to 5V
Operating: 0 to 50 C, Stored:
3%F.S. or less of measured pressure at 25 C in temperature range of 0 to 50 C
Pressure receiving area: Stainless steel SUS 630, Fittings: Stainless steel SUS 304
Can correct the pressure set point value of switch output according to fluctuations in the primary pressure.
Prevents malfunction due to sudden fluctuations in the primary pressure by adjusting the response time.
The key board operation can be locked to prevent incorrect operation on the operation switch.
Can retain the maximum pressure value displayed during measurement.
Can retain the minimum pressure value displayed during measurement.
The pressure display can be set at zero when the pressure is open to the atmosphere.
Note 1)
Can convert the display value (for overseas use only).
100 to 100kPa
100 to 100kPa
500kPa
0.1
0.001
0.001
0.02
1
0.1
Fluid that will not corrode stainless steel SUS 630 and 304
12 to 24VDC, Ripple (p-p) 10% or less
55mA or less (With no load)
1 digit or less
Variable (0 or above)
Fix (3 digits)
With short circuit protection
3 1/2 digit LED display (Sampling frequency: 5 times/sec)
2% F.S. 1 digit or less (With ambient temperature of 25
5% F.S. or less
No-voltage input (solid state switch or reed switch), input 5ms or more
10 to 60 C (With no condensation or freezing)
Operating and stored: 35 to 85% RH (With no condensation)
250VAC for 1 min, between all lead wires and enclosure
2MΩ or more (at 50VDC) between all lead wires and enclosure
10 to 500Hz with 1.5mm amplitude or 98m/s
980m/s 2 in X, Y, Z directions 3 times each (Not energized)
02: R 1/4, M5 x 0.8
5 wire oil proof heavy duty cable (0.15mm
Approx. 120g (Each including 3m lead wire)
Note
The possible set ranges for types with auto shift function are as follows:
Regulating pressure range
ZSE50F/ISE50
Series
ISE50 (Positive pressure)
0.000 to 1.000MPa
0.100 to 1.000MPa
1.5MPa
0.001
0.01
0.01
0.1
0.3% F.S.
Note 4)
Output voltage: 1 to 5V
IP65
2 , whichever is smaller
T2: NPT 1/4, M5 x 0.8
2 )
100.0 to 100.0kPa
0.1 to 1.000MPa
1 digit or less
3 C)
2.5% F.S. or less
Possible set range
100.0 to 100.0kPa
1.000 to 1.000MPa
Page 5
Page 16
2