Package Contents - Wayne-Dalton 9800 Installation Instructions And Owner's Manual

NOTE: Drill a 3/16" pilot hole in the mounting surface to avoid splitting the lumber. Do not
attach the mounting surface with nails.
WEATHERSTRIPS (MAY NOT BE INCLUDED):
Depending on the size of your door, you may have to cut or trim the weatherstrips (if neces-
sary) to properly fit into the header and jambs.
NOTE: If nailing product at 40°F or below, pre-drilling is required.
NOTE: Do not permanently attach weatherstrips to the header and jambs at this time.
FOR QUICK INSTALL TRACK: For the header, align the weatherstrip with the inside edge
of the header and temporarily secure it to the header with equally spaced nails. Starting
at either side of the jamb, fit the weatherstrip up tight against the temporarily attached
weatherstrip in the header and flush with the inside edge of the jamb. Temporarily secure
the weatherstrip with equally spaced nails. Repeat for other side. This will keep the bottom
section from falling out of the opening during installation. Equally space nails approximately
12" to 18" apart.
FOR FULLY ADJUSTABLE TRACK: For the header, align the weatherstrip 1/8" to 1/4" inside
the header edge, and temporarily secure it to the header with equally spaced nails. Starting
at either side of the jamb, fit the weatherstrip up tight against the temporarily attached
weatherstrip in the header and 1/8" to 1/4" inside the jamb edge. Temporarily secure the
weatherstrip with equally spaced nails. Repeat for other side. This will keep the bottom sec-
tion from falling out of the opening during installation. Equally space nails approximately 12"
to 18" apart.
HEADROOM REQUIREMENT: Headroom is defined as the space needed above the top of
the door for tracks, springs, etc. to allow the door to open properly. If the door is to be motor
operated, 2-1/2" (64 mm) of additional headroom is required.
NOTE: 6" low headroom conversion kit is available for 12" radius only. Contact your local
Wayne Dalton dealer.
BACKROOM REQUIREMENT: Backroom is defined as the distance needed from the opening
back into the garage to allow the door to open fully.
BACKROOM REQUIREMENTS
Door Height Track
6'0" to 7'0" 15" Radius
7'1" to 8'0" 15" Radius
8'1" to 9'0" 15" Radius
9'1" to 10'0" 15" Radius
10'1" to 12'0" 15" Radius
12'1" to 14'0" 15" Radius
HEADROOM REQUIREMENTS
Track Type
15" Radius
Headroom
Suitable mounting surface
2"x 6" lumber minimum
Header board 2"x 6"
lumber preferred
Min. Side
room
Clearance
Finished
is 3-1/2"
Door
Height
Plumb
jambs
Manual Lift Motor Operated
102" (2591 mm) 125" (3175 mm)
114" (2896 mm) 137" (3480 mm)
126" (3200 mm) 168" (4267 mm)
138" (3505 mm) 168" (4267 mm)
162" (4115 mm) See *NOTE
186" (4724 mm) See *NOTE
Space Needed
14-1/2" (368 mm)
Min. Side
room
Clearance
is 3-1/2"
Nail
Weather
seal
Jamb
Door
Stop
Jamb
Quick Install track
Weather
seal
Jamb
1/8" to 1/4"
Door
Stop
Jamb
1/8" to 1/4"
Other track systems

Package Contents

NOTE: Depending on the door model, some parts listed will not be supplied if not required.
Rear Back Hangs may not be included with your door.
Quick Install flag angles
RH/LH (as required)
Angle mount vertical track assemblies RH/LH (as required)
(2) Horizontal angles (as required)
Q.I. jamb brackets F.A. jamb brackets
(as required) (as required)
Weatherstrips & nails Door stop & nails
(If included) (If included)
Top fixture assemblies Roller spacers
(as required) (as required)
Counterbalance lift cables Torsion springs RH/LH
3
Door sections (as required)
Torsion shaft / Torsion keyed shaft (as required)
Torsion keyed shafts (as required)
Fully Adjustable flag angles
RH/LH (as required)
Vertical tracks RH/LH (as required)
Riveted vertical track assemblies RH/LH (as required)
Horizontal tracks RH/LH (as required)
Windload Jamb Drawbar operator
brackets (as required) bracket (if included)
Pull Down rope
(if included)
Strut (U-shaped) Hinge reinforcing brackets
(if included) RH/LH (as required)
End bearing bracket RH/LH (as required)
Track rollers
(as required)