Package Contents - Wayne-Dalton Torsion 9800 Installation Instructions And Owner's Manual

NOTE: Drill a 3/16" pilot hole in the mounting surface to avoid splitting the lumber. Do not
attach the mounting surface with nails.
WEATHERSTRIPS (MAY NOT BE INCLUDED):
Depending on the size of your door, you may have to cut or trim the weatherstrips (if neces-
sary) to properly fit into the header and jambs.
NOTE: If nailing product at 40°F or below, pre-drilling is required.
NOTE: Do not permanently attach weatherstrips to the header and jambs at this time.
FOR QUICK INSTALL TRACK: For the header, align the weatherstrip with the inside edge
of the header and temporarily secure it to the header with equally spaced nails. Starting
at either side of the jamb, fit the weatherstrip up tight against the temporarily attached
weatherstrip in the header and flush with the inside edge of the jamb. Temporarily secure
the weatherstrip with equally spaced nails. Repeat for other side. This will keep the bottom
section from falling out of the opening during installation. Equally space nails approximately
12" to 18" apart.
FOR FULLY ADJUSTABLE TRACK: For the header, align the weatherstrip 1/8" to 1/4" inside
the header edge, and temporarily secure it to the header with equally spaced nails. Starting
at either side of the jamb, fit the weatherstrip up tight against the temporarily attached
weatherstrip in the header and 1/8" to 1/4" inside the jamb edge. Temporarily secure the
weatherstrip with equally spaced nails. Repeat for other side. This will keep the bottom sec-
tion from falling out of the opening during installation. Equally space nails approximately 12"
to 18" apart.
HEADROOM REQUIREMENT: Headroom is defined as the space needed above the top of
the door for tracks, springs, etc. to allow the door to open properly. If the door is to be motor
operated, 2-1/2" (64 mm) of additional headroom is required.
NOTE: 6" low headroom conversion kit is available for 12" radius only. Contact your local
Wayne Dalton dealer.
BACKROOM REQUIREMENT: Backroom is defined as the distance needed from the opening
back into the garage to allow the door to open fully.
BACKROOM REQUIREMENTS
Door Height Track
6'0" to 7'0" 6" Low Headroom
7'1" to 8'0"
8'1" to 9'0"
9'1" to 10'0"
10'1" to 12'0"
12'1" to 14'0"
HEADROOM REQUIREMENTS
Track Type
6" Low Headroom
Headroom
Suitable mounting surface
2"x 6" lumber minimum
Header board 2"x 6"
lumber preferred
Min. Side
room
Clearance
Finished
is 3-1/2"
Door
Height
Plumb
jambs
Manual Lift Motor Operated
108-1/2" (2756 mm) 125" (3175 mm)
120-1/2" (3061 mm) 137" (3480 mm)
132-1/2" (3366 mm) 168" (4267 mm)
144-1/2" (3670 mm) 168" (4267 mm)
168-1/2" (4280 mm) See *NOTE
192-1/2" (4890 mm) See *NOTE
Space Needed
6" (152 mm)
Min. Side
room
Clearance
is 3-1/2"
Nail
Weather
seal
Jamb
Door
Stop
Jamb
Quick Install track
Weather
seal
Jamb
1/8" to 1/4"
Door
Stop
Jamb
1/8" to 1/4"
Other track systems

Package Contents

NOTE: Depending on the door model, some parts listed will not be supplied if not required.
Rear Back Hangs may not be included with your door.
Quick Install flag angles
RH/LH (as required)
Fully Adjustable jamb
Quick install jamb
brackets (as required)
brackets (as required)
Drawbar operator
bracket (if included)
Oval Bearings
(as required) Cable drums RH/LH
Center bracket bushing
Center bearing bracket
assembly (as required)
assembly (as required)
3
Door sections (as required)
Torsion shaft or Torsion keyed shaft (as required)
Torsion keyed shafts (as required)
Fully Adjustable flag angles
RH/LH (as required)
Riveted vertical track assemblies RH/LH (as required)
Vertical tracks RH/LH (as required)
Wall angle track assemblies RH/LH (as required)
Horizontal tracks RH/LH
Door stop & nails
Pull down
Weatherstrips & nails
rope (if included)
Track rollers
(as required)
(2) Top fixtures
Torsion springs RH/LH
Center coupler
(2) Cable
lift sheaves
(If included)
(If included)
Keys
(as required)
assembly
(as required)