Package Contents - Wayne-Dalton TORQUEMASTER PLUS Installation Instructions And Owner's Manual

be firmly attached to the wall, above the header at the center of the opening.
NOTE: Drill a 3/16" pilot hole in the mounting surface to avoid splitting the lumber. Do not
attach the mounting surface with nails.
WEATHERSTRIPS (IF APPLICABLE): Depending on the size of your door, you may have to
cut or trim the weatherstrips (if necessary) to properly fit into the header and jambs.
NOTE: If nailing product at 40°F or below, pre-drilling is required.
For the header, align the weatherstrip with the inside edge of the header and temporarily
secure it to the header with equally spaced nails. Starting at either side of the jamb, fit the
weatherstrip up tight against the temporarily attached weatherstrip in the header and flush
with the inside edge of the jamb. Temporarily secure the weatherstrip with equally spaced
nails. Repeat for other side. This will keep the bottom section from falling out of the opening
during installation. Equally space nails approximately 12" to 18" apart.
HEADROOM REQUIREMENT: Headroom is defined as the space needed above the top of
the door for tracks, springs, etc. to allow the door to open properly. If the door is to be motor
operated, 2-1/2" (64 mm) of additional headroom is required.
NOTE: 6" low headroom conversion kit is available for 12" radius only. Contact your local
Wayne Dalton dealer.
BACKROOM REQUIREMENT: Backroom is defined as the distance needed from the opening
back into the garage to allow the door to open fully.
BACKROOM REQUIREMENTS
DOOR HEIGHT TRACK
6'5" to 7'0" 12",15" Radius
7'1" to 8'0" 12",15" Radius
HEADROOM REQUIREMENTS
TRACK TYPE
15" Radius track
12" Radius track
6" LHR KIT
Headroom
Suitable mounting surface
2"x 6" lumber minimum
Header board 2"x 6"
lumber preferred
Min. Side
room
Clearance
Finished
is 3-1/2"
Door
Height
Plumb
jambs

Package Contents

NOTE: Depending on the door model, some parts listed will not be supplied if not required.
Rear Back Hangs are not included with your door.
MANUAL LIFT MOTOR OPERATED
98" (2489 mm) 125" (3175 mm)
110" (2794 mm) 137" (3480 mm)
SPACE NEEDED
13-1/2" (343 mm)
11" (279 mm)
6" (152 mm)
Min. Side
room
Clearance
is 3-1/2"
Nail
Jamb
Quick Install track
Weatherstrips
(E1. - E4.) Door sections (as required)
(A1.) Quick Install flag angles
RH/LH (as required)
Weatherstrips (B1.) Quick install jamb
brackets (as required)
(If included)
(I4.) Right
(I5.) Cable drum
__
s __
rn 0
Tu 16/ 202
g 3 12/
rin REV
d Sp assemblies RH/LH
al le
hand end bracket st 300 547
r of In
n, orati a on
be Way ne Dalto Corp
N um ht 2020 head Door
pyrig of Over
©Co divis ion
(F2.) Top fixture
(F1.) Top fixture bases slides
(2) 5/16"-18 Hex nuts (2) 3/8"- 16 Hex nuts
5/16" x 1-5/8" Hex head lag screws
1/4"-20 x 9/16"
Track bolts (as required)
1/4"-14 x 5/8" Self tapping
screws (as required)
5/16" x 1-1/4" Clevis pin
3
(I2.) Spring tube assembly
(A2.) Fully Adjustable flag angles
RH/LH (as required)
(H5. - H6.) Vertical tracks RH/LH
(H1. - H2.) Horizontal tracks RH/LH
(H3. - H4.) Horizontal track angles
(I3.) Left hand end
(I1.) Center bracket
bushing assembly bracket (as required)
(I6.) Idler bracket (C1.) Track rollers
(single spring only)
(J1.) Strut
(G1.) Drawbar (U-shaped) (A-symmetrical)
operator bracket
(if included)
1/4"- 20 Flanged
hex nuts (as required) (2) 5/16" Washers
(2) #12 x 1/2"
(as required) Phillips head screws
(2) 5/16"-18 x 3/4"
(2) 3/8"-16 x 3/4"
Carriage bolts
Truss head bolts
Rear Back Hangs
(If included)
(as required)
(J2.) Strut
(if included)
Stud Plate
(as required)
Cotter pin