Page 1
Notes Manual of Installation, Use, and Maintenance In Between Jambs Without Integrated Operator Models: Wayne-Dalton Optimal, Wayne-Dalton Confort, Wayne-Dalton Diffusion, Wayne-Dalton Prestige+/40mm/Pinnacle Wayne-Dalton Europe 1 Rue Maurice Hollande 51100 Reims, France www.waynedaltoneurope.com NOTE: THIS NOTES MANUAL MUST BE ACCOMPANIED BY THE DRAWINGS MANUAL, PART NR. 324623.
TABLE OF CONTENTS Notes of Installation, Use, and Maintenance Definition Of Symbols ..............................3. Important Safety Instructions For Installation ........................3. Package Contents ................................4. Required Tools ................................4. “INSTALLATION” Door Assembly Mounting ............................5. Horizontal Track Mounting ............................5. Spreader Bar Pre-mounting ............................
DEFINITION OF SYMBOLS WARNING ATTENTION - Risk Of Injury WARNING IT IS VITAL FOR THE SAFETY OF PERSONS TO FOLLOW ALL INSTRUCTIONS.SAVE THESE INSTRUCTIONS. 1. READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS. 2. Wear eye protection when using tools to install, repair, or adjust door or opener to prevent eye injuries. 3.
Note: Use these notes of installation, Use, and Maintenance in conjunction with the Drawings of installation, Use, and maintenance to perform the installation. The following letters & numbers in parenthesis, [example: (a1)] cross reference items listed in each diagram of the Drawings of Installation, Use, and Maintenance manual.
Installation IMPORTANT: Stainless steel lag screws or PT2000 coated lag screws must be used when installing center bearing brackets, end bearing brackets, jamb brackets, operator mounting / support brackets and disconnect brackets on treated lumber (preservative-treated). Stainless steel or PT2000 coated lag screws are not necessary when installing products on un-treated lumber.
Spreader Bar Pre-Mounting (See Diagram 3 on page 5 of Drawings of Installation, Use and Maintenance manual) Attach the “L” bracket (A4.3) to the right side of the slider bar (A4.2) with one ø6x15mm (1/4” - 20 x 9/16”) track bolt (A6) and Tools Needed: ø6mm (1/4”...
Striker Plate Mounting (If Required) (See Diagram 5 on page 6 of Drawings of Installation, Use and Maintenance manual) Tools Needed: IMPORTANT: If the door is electrically operated, the secure lock MUST NOT be installed. In which case, skip this step. 11mm (7/16”) Locate desired side of door for striker plate placement.
Spring Adjustment (If Required) - Continued (See Diagram 7 on page 6 of Drawings of Installation, Use and Maintenance manual) Tools Needed: Let wrench rotate clockwise for the right side, counter clockwise for the left side until desired tension is achieved as shown in FIG.
MONTHLY MAINTENANCE WARNING KEEP AWAY FROM ALL MOVING PARTS OF THE DOOR AND OPENER SYSTEM WHILE THE SYSTEM IS BEING OPERATED. WARNING NEGLIGENT OR IMPROPER MAINTENANCE INCREASES THE RISK OF INJURY TO PERSONS AND DAMAGE TO PROPERTY. WARNING TORQUEMASTER™ COUNTERBALANCE SYSTEM AND CABLES ARE UNDER EXTREME TENSION! NEVER TAMPER WITH THE TORQUEMASTER™...
MAINTENANCE / PAINTING INSTRUCTIONS FOR PRE-PAINTED DOORS MAINTENANCE While factory-applied finishes on steel garage doors are durable, it is desirable to clean them on a routine basis. Some discoloration of the finish may occur when a door has been exposed to dirt-laden atmosphere for a period of time. Slight chalking may also occur as a result of direct exposure to sunlight.
LIMITED WARRANTY 1. The manufacturer (Wayne-Dalton Corp.) warrants the Optimal steel garage door sections from the time of installation, for a period of ten years against structural failure of the door section(s) (rendering the door inoperable) due to separation / degradation of the foam insulation.
Questions? Need Information? Visit our website: www.waynedaltoneurope.com Thank you for your purchase Models: Wayne-Dalton Optimal, Wayne-Dalton Confort, Wayne-Dalton Diffusion, Wayne-Dalton Prestige+/40mm/Pinnacle Covered under one or more of the following U.S. patents: D413,055/D413,579/D413,867/D421,031/D466,141/D472,568/D472,910/D473,573/D473,574/D474,215/D475,146/5,259,143/5,408,724/5 ,409,051/5,419,010/5,929,580/5,931,212/6,078,249/6,145,570/6,164,014/6,253,824/6,263,947/6,325,134/6,326,751/6,326,754/6,401,7 92/6,442,897/6,561,255/6,561,256/6,568,454/6,605,910/6,588.156/6,640,872/6,667,591/6,672,362/6,739,372/6,899,157 European Patent: EP0975417 other U.S. and foreign patents pending.