Package Contents - Wayne-Dalton 8000 Installation Instructions And Owner's Manual

NOTE: Drill a 3/16" pilot hole in the mounting surface to avoid splitting the lumber. Do not
attach the mounting surface with nails.
WEATHERSTRIPS (MAY NOT BE INCLUDED):
Depending on the size of your door, you may have to cut or trim the weatherstrips (if neces-
sary) to properly fit into the header and jambs.
NOTE: If nailing product at 40°F or below, pre-drilling is required.
NOTE: Do not permanently attach weatherstrips to the header and jambs at this time.
For the header, align the weatherstrip 1/8" to 1/4" inside the header edge, and temporarily
secure it to the header with equally spaced nails. Starting at either side of the jamb, fit the
weatherstrip up tight against the temporarily attached weatherstrip in the header and 1/8"
to 1/4" inside the jamb edge. Temporarily secure the weatherstrip with equally spaced nails.
Repeat for other side. This will keep the bottom section from falling out of the opening during
installation. Equally space nails approximately 12" to 18" apart.
HEADROOM REQUIREMENT: Headroom is defined as the space needed above the top of
the door for tracks, springs, etc. to allow the door to open properly. If the door is to be motor
operated, 2-1/2" (64 mm) of additional headroom is required.
NOTE: 6" low headroom conversion kit is available for 12" radius only. Contact your local
Wayne Dalton dealer.
BACKROOM REQUIREMENT: Backroom is defined as the distance needed from the opening
back into the garage to allow the door to open fully.
*NOTE: For door heights from 10'1" to 14'0", refer to your operator manufacture installation
instructions for appropriate depth into room.
BACKROOM REQUIREMENTS
Door Height Track
6'0" to 7'0" 12", 14" Radius
7'1" to 8'0" 12", 14" Radius
8'1" to 9'0" 12", 14" Radius
9'1" to 10'0" 12", 14" Radius
10'1" to 12'0" 12", 14" Radius
12'1" to 14'0" 12", 14" Radius
HEADROOM REQUIREMENTS
Track Type
12" Radius
14" Radius
Headroom
Suitable mounting surface
2"x 6" lumber minimum
Header board 2"x 6"
lumber preferred
Min. Side
room
Clearance
Finished
is 3-1/2"
Door
Height
Plumb
jambs

Package Contents

NOTE: Depending on the door model, some parts listed will not be supplied if not required.
Rear Back Hangs may not be included with your door.
Manual Lift Motor Operated
102" (2591 mm) 125" (3175 mm)
114" (2896 mm) 137" (3480 mm)
126" (3200 mm) 168" (4267 mm)
138" (3505 mm) 168" (4267 mm)
162" (4115 mm) See *NOTE
186" (4724 mm) See *NOTE
Space Needed
13-1/2" (343 mm)
14-1/2" (368 mm)
Min. Side
room
Clearance
is 3-1/2"
Nail
Weatherstrips
Jamb
1/8" to 1/4"
Angle mount vertical track assemblies RH/LH (as required)
Track rollers
Jamb brackets
(as required)
(as required)
Top fixture assemblies Top fixture slides
(as required) (as required)
Strut (U-shaped)
Bottom corner brackets
(if included)
RH/LH (as required)
(2) Step plates (2) Lift handles &
(as required) Spacers
Head plates RH/LH
(as required)
Keys
Cable drums RH/LH
(as required)
3
Door sections (as required)
Torsion shaft / Torsion keyed shaft (as required)
Torsion keyed shafts (as required)
Vertical tracks RH/LH
Horizontal tracks RH/LH
Flag angles RH/LH
Weather seals & nails
Pull Down rope
(If included)
Bottom corner brackets
Top fixture bases
RH/LH (as required)
(as required)
Graduated
hinges (as required)
spacers (as required)
Counterbalance lift cables Torsion springs RH/LH
Head plates RH/LH Spring anchor bearing
(as required)
Center coupler
assembly
Spring anchor bracket
(as required)
(if included)
(2) Roller
(as required)
(as required)