Wayne-Dalton 9100 Quick Start Manual
Torquemaster plus series residential standard lift
Hide thumbs
Also See for 9100:
- Installation instructions and owner's manual (36 pages) ,
- Installation manual (36 pages) ,
- Installation instruction and owenrs manual (22 pages)
Table of Contents
Advertisement
Models 9100 / 9405
/ 9605
T
M
o r q u e
a s T e r
r
esidenTial
s
l
Tandard
ifT
q
s
G
uick
TarT
uide
PLEASE DO NOT RETURN THIS PRODUCT
TO THE STORE
If you need assistance, please call 1-866-
569-3799 (press Option 1) and follow the
prompts to contact a customer service
representative. They will be happy to handle
any questions that you may have.
©Copyright 2017
Wayne Dalton, a division of Overhead Door Corporation
P
®
l u s
T a b l e O f C o n t e n t s
QUICK START GUIDE IMPORTANT NOTICES!
This Quick Start Guide is only meant to be used as an aid and
/ or introduction to garage door installation, and does not replace the
complete Installation Instructions and Owner's manual available on the
web at www.Wayne-Dalton.com. Wayne Dalton highly recommends
that you read and fully understand the Installation Instructions and
Owner's Manual before you attempt this installation.
To avoid possible injury, read and fully understand the enclosed
instructions carefully before installing and operating the garage door. Pay
close attention to all warnings and notes. After installation is complete,
fasten this manual near garage door for easy reference.
The complete Installation Instructions and Owner's Manual are available at no
charge from:
- Your local Wayne Dalton Sales Center, or
- Online at www.Wayne-Dalton.com, or
- By mailing to: Wayne Dalton, a division of Overhead Door Corporation, P.O. Box
67, Mt. Hope, OH., 44660
Part Number
348708
2
2
2
3
4
5
9
9
10
10
10
10
REV9_08/02/2017
Advertisement
Table of Contents
Related Manuals for Wayne-Dalton 9100
Summary of Contents for Wayne-Dalton 9100
-
Page 1: Table Of Contents
If you need assistance, please call 1-866- complete Installation Instructions and Owner’s manual available on the web at www.Wayne-Dalton.com. Wayne Dalton highly recommends 569-3799 (press Option 1) and follow the that you read and fully understand the Installation Instructions and prompts to contact a customer service Owner’s Manual before you attempt this installation. -
Page 2: Pre-Installation
Existing Door & Prepar- proper tools and instructions. ing the Opening. These are available for download at www.Wayne-Dalton.com or at your local Wayne Dalton Sales Center. 12. On electrically operated doors, pull down ropes must be removed and locks must be removed or made inoperative in the open (unlocked) position. -
Page 3: Breakdown Of Parts
BREAKDOWN OF PARTS NOTE: The illustrations shown on this page are general representations of the door parts. Each specific door models may have unique variations. A. FLAG ANGLES (AS REQUIRED): I1. Left Hand Horizontal Track Assembly A1. Fully Adjustable (F.A.) Flag Angles I2. -
Page 4: Door Installation Instructions
NOTE: Verify bottom weather seal is aligned with bottom section. If there is more than 1/2” DOOR INSTALLATION excess weather seal on either side, trim weather seal even with bottom section. Positioning Bottom Section INSTRUCTIONS Before installing your door, be certain that you have read and followed all of the instruc- tions covered in the pre-installation section of this manual. -
Page 5: Counterbalance Installation Instructions
Attaching Top Fixtures To Top Section Adjusting Top Fixtures To install the top fixtures, align the top holes in the top fixture base with the second set of With horizontal tracks installed, you can now adjust the top fixtures. Vertically align the top holes in the end cap of the top section. - Page 6 NOTE: Working with a partner as needed, lift Flag angle the TorqueMaster spring tube assembly up Cam peak ® Counterbalance lift and rest it on top of the flag angles. straight up cable 1/2 pre-wrap TorqueMaster ® Right hand cable spring tube drum assembly assembly...
- Page 7 Adjusting Counterbalance Lift Cable Left hand Left hand cable drum cable drum Bearing Flag Idler bracket angle Starting on the right side, adjust the cable drum assembly by rotating the drum until the set TorqueMaster screw faces directly away from the header. The position of the cam peak on the TorqueMas- ®...
- Page 8 ratchet wheel or the mark on the winding shaft. After 2 to 3 turns, remove the ratchet wrench Cable Left hand and adjust the counterbalance lift cable on the left side. Ensure counterbalance lift cables are drum drum wrap in the first groove of the cable drums, as shown in Step Adjusting Counterbalance Lift Cable. NOTE: Single spring applications require no spring winding on the left hand side, but lift Last cable tension needs to be adjusted.
-
Page 9: Maintenance
IMPORTANT: TO ADJUST SPRINGS, ONLY ADD OR REMOVE A MAXIMUM OF 3/10 OF To clean polycarbonate windows, see www.Wayne-Dalton.com. A TURN (THREE TEETH ON THE RATCHET WHEEL) AT A TIME. BOTH SIDES NEED TO BE... -
Page 10: Painting Your Garage Door
Wayne Dalton, a division of Overhead Door Corporation (“Seller”) war- the opening. If you suspect problems, contact a trained door system technician. rants to the original purchaser of the Models 9100, 9405 and 9605 (“Product”), WARNING subject to all of the terms and conditions hereof, that the Product and all... - Page 11 house in which the Product is originally installed. • TWO (2) YEARS on the Model 9405 factory attached overlay material against peeling, cracking, chalking, fading or delamination. Seller’s obligation under this warranty is specifically limited to repairing or replacing, at its option, any part which is determined by Seller to be defec- tive during the applicable warranty period.
- Page 12 Thank you for your purchase. PLEASE DO NOT RETURN THIS PRODUCT TO THE STORE If you need assistance, please call 1-866-569-3799 (press Option 1) and follow the prompts to contact a customer service representative. They will be happy to handle any questions that you may have.