Page 3
In this manual, you will find everything there is to know about possible applications of your sewing computer. Should any questions remain unanswered, we kindly ask you to turn to your dealer. We wish you much pleasure and great sewing successes! Questions concerning machine, service and customer care KONTAKT CONTACT www.veritas-sewing.com/en/service...
Important Safety Instructions When using an electrical appliance, basic safety instructions 5. Keep your fingers away from all moving parts. Increased cau- should always be followed. Please read through this user manual tion is called for in the vicinity of the sewing needle. Moving thoroughly before using your sewing computer and keep these parts such as needle, presser foot lifter, etc.
Page 5
Important Safety Instructions 13. Neither tug nor rip on the cloth while sewing – that might 26. Your sewing computer is equipped with a LED light. If the overly bend the needle, causing it to break. LED light is damaged, it has to be replaced by the manufac- turer or its customer service to prevent danger.
Content Important safety instructions..........4-5 Stitch length adjustment buttons ........35 Walking foot ...................65 Principal parts of the machine ...........7 Mode selection button ............35 Fagoting ...................66 Machine control buttons ............8-9 Mirror button ................36 Decorative topstitching ..............67 LCD screen ..................10 Direct mode for selection 83 standard stitches ..37 Scallop stitch ..................68 Stitch overview................11 Number buttons for selecting patterns...
W P rincipal Parts of the Machine Principal Parts of the Machine 1 Stitch pattern plate (plate thereby, the clip is in the accessory box) 2 Tension dial 3 Bobbin thread guide 4 Face plate 5 Operation buttons (A) 6 Thread cutter 7 Buttonhole lever 8 Auto needle threader 9 Needle plate cover...
Machine Control Buttons A. Operation buttons (see page 67) 1 START/STOP button Press this button to start or stop the machine. 2 Thread cutter button Press this button after finishing sewing and the machine will trim the threads. 3 Reverse button Hold down this button to sew stitches in reverse or sew reinforcement stitches at a low speed.
Page 9
W M achine Control Buttons C. Memory buttons (see page 83) Memory button Press the M button to enter or store the created pattern combination in the memory. 12 Arrow buttons Press the button until the actual stitch number is displayed.
LCD-Screen Direct Pattern 1 Pattern number 2 Direct mode for selecting standard stitches 3 Pattern 4 Suggested presser foot Meaning of the symbols 5 Needle position 6 Bobbin winding 7 Buttonhole lever 8 Mirror 9 Needle up 10 Auto-lock 11 Reverse Raise Raise Lower...
W B efore first use Before first use Please note that improper handling of electrical currents can be lethal. Therefore, please read the safety meas- ures on page 8 and the following safety precautions: • Make sure that children do not get the opportunity to play with the sewing machine! •...
Power Source CAUTION: Always make sure that the machine is unplugged from power source and the main switch is on „O“ when the machine is not in use and before inserting or removing parts (f.e. changing the needle). Connecting the machine to the power source Before connecting the power supply, make sure that the voltage and frequency shown on the machine is...
W P resser Foot ATTENTION: Turn power switch to off („O“) position when changing the presser foot. Attaching / changing the presser foot Attaching the presser foot holder 1. Raise the presser foot bar (a) by raising the presser foot lifter. 2.
Winding the Bobbin Winding the bobbin Place the thread and spool holder onto the spool pin. For larger spools of thread, place the large side of the spool holder toward the spool. For smaller spools of thread, place the small side of the spool holder toward the spool, or use the small spool holder.
Page 17
W W inding the Bobbin Winding the bobbin When the bobbin winder spindle is pushed to the right, which is the „bobbin winding position“, the symbol appears on the LCD screen. The symbol will disappear from the LCD screen when the bobbin winder spindle is pushed to the left, which is the „sewing position“.
Inserting the Bobbin Inserting the bobbin When inserting or removing the bobbin, the needle must be fully raised, therefore press the button „Needle up / down“. Raise also the presser foot. Then turn off the machine. ATTENTION: Turn power switch to off („O“) before inserting or removing the bobbin.
W U pper Thread Threading the upper thread NOTE: Threading the upper thread is very easy. It is important to carry out the threading correctly as by not doing so several sewing problems could result. First turn on the machine with the power switch (position “–“).
Page 20
Upper Thread Threading the upper thread Guide the thread around the thread guide pull- ing the thread through the pre-tension spring as illustrated. Guide the thread into the right slot and pass it downwards. Then, down and around the check spring holder and up again.
W N eedle Threader ATTENTION: Turn power switch to the off position („O“). IMPORTANT: The needle was raised before to its highest position (with the button “Needle up/down”). Lower the presser foot. Using the needle threader Lower the needle threader lever slowly and draw the thread through the thread guide as illustrated and then to the right.
Drawing up the lower thread Drawing up the lower thread Hold the upper thread with the left hand. Turn the handwheel towards you (counterclockwise) lower- ing, then raising the needle. Gently pull on the upper thread to bring the bobbin thread up through the needle plate hole.
W A djustments Cutting the thread Raise the presser foot. Remove the fabric, draw the threads to the left side of the face cover and cut using the thread cutter. The threads are cut at the proper length to start the next seam.
Sewing Starting sewing Start / Stop button The Start/Stop button can be used to run the machine when the foot controller is unplugged from the machine. Press the button to start sewing, then press it again to stop sewing. The machine will run slowly at the start of sewing.
W T hread tension Thread tension – Basic thread tension setting is „4“. – To increase the tension, turn the dial to the next number up. – To decrease the tension, turn the dial to the next number down. Proper setting of tension is important for good sewing.
Presser Foot Chart The twin needle can be used for some stitches, offering more stitching options. For more information, go to the section „Using the twin needle“. General sewing, Overcasting Patchwork stitches, Decorative stitching, Smocking, Fagoting, etc. Overcasting foot (E) All purpose foot (T) Inserting zippers Blind hem stitching...
W R eplacing the needle / Feed dogs Replacing the needle ATTENTION: Turn power switch of off („O“) po- sition when carrying out any of the operations shown below. Change the needle regularly, especially if it is showing signs of wear and causing problems. Insert the needle following the illustrated instructions.
Pattern Balance Adjustment Pattern balance adjustment If decorative stitch patterns, letter, numbers or the manual buttonhole are uneven when sewn on a particular fabric, adjust them with the pattern adjust- ment dial. Use a coin or a screwdriver to turn the dial slightly toward the „+“...
W O peration Buttons The most important functions at a glance A Needle up / down position button B Auto-lock button C Reverse button D Thread cutter button E Start / Stop button F Speed limiting adjustment lever Start/Stop button The machine will start running when Start/Stop but- ton is pressed and will stop when pressed the second time.
Operation Buttons Using the foot control: The most important functions When you are sewing with one of these stitches or at a glance patterns and then press the reverse sewing button, the machine will sew in reverse until you release the 2.
W O peration Buttons The most important functions at a glance 3. Needle up/down position button With the „Needle up / down“ button, you decide whether the needle shall stop in the up position or in the material when you stop sewing. NOTE: Always press the button before starting sewing.
Operation Buttons The most important functions at a glance A Stitch width adjustment buttons B Stitch length adjustment buttons C Mirror button D Mode selection button Stitch width adjustment button (B) When you select a stitch, the machine will auto- matically set the recommended stitch width, which will be indicated by numbers on the LCD screen.
W O peration Buttos The most important functions at a glance Stitch length adjustment buttons (A) When you select a stitch the machine will automati- cally set the recommended stitch length which will be indicated by numbers on the LCD screen. The stitch length can be adjusted by pressing the stitch length adjustment buttons.
Operation Buttons The most important functions at a glance Mirror button (C) (see page 147) The Direct Patterns 1–7 and Patterns 00–14, 27–99 can be mirror imaged along a vertical axis by pressing button. The LCD will display the mirror function and the machine will continue to sew the reflected pattern until the mirror function is pressed again to cancel the mirror function.
Selection Buttons 1. Memory button Press the button to enter the memory mode, and store the combinations of characters or decorative stitches. Press the button again to leave the memory mode and return to „Direct“ mode. Please note: The Direct Patterns and Patterns 15–26 cannot be memorized.
Selection Buttons Direct pattern selection and number buttons Direct pattern selection Press the buttons to select the utility patterns shown beside the number buttons, when the mode button is set at the „Direct“ mode. Number buttons Press the number buttons for selecting the pattern needed.
W S ewing Tips Sewing corners 1. Stop the sewing machine when you reach a corner. 2. Lower the needle into the fabric manually or by pressing the needle up / down button once. 3. Raise the presser foot. 4. Use the needle as a pivot and turn the fabric 90°. 5.
Sewing Tips Installing the extension table The Extension Table is an optional accessory. 1. Pull the sewing table and accessory box off by sliding it to the left. 2. Follow the arrow, and stretch the foot of the extension table. 3.
W N eedle Position and Stitch Length Changing the needle position and stitch B-05 length Changing the needle position These setting apply only to Direct Patterns 1– 4 or B Group Patterns 01. The pre-set position is „3.5“, center position. When you press the ”−“ of stitch width adjustment button, the needle position will be moved to the left.
Zigzag Stitches Zigzag stitches B-08 Adjusting the stitch width The maximum stitch width for zigzag stitching is ”7.0“; however, the width can be reduced for most patterns. The width increases or decreases as you press the ”+“ or ”−“ stitch width adjustment buttons from ”0.0 –7.0“.
Stretch Stitches Stretch stitches Stretch stitches are strong and flexible and will give with the fabric without breaking. Good for easy to ravel and knit fabrics. It is good for joining durable fabric such as denims. These stitches can also be used as a decorative top stitch.
Overcasting Stitches Overcasting foot 1. Change the presser foot to the overcasting foot. 2. Sew the fabric with the fabric edge against the guide of the overcasting foot. ATTENTION: The overcasting foot should be used to sew with Direct Patterns 05 and 08 only.
Blind Hems Blind hems B-11 B-12 B-11: Blind hem for woven fabrics B-12: Blind hem for stretch fabrics NOTE: It takes practice to sew blind hems. Always make a sewing test first. 1. Fold the fabric as illustrated with the wrong side uppermost.
Button Sewing Button sewing B-26 Select the pattern 26 from the Group Patterns ”B“ to ➊ get the button sewing stitch. Change the presser foot to the button sewing foot. Move the drop feed lever to to lower the feed ▲▲...
Page 47
B-22 W B uttonhole sewing Buttonhole sewing For light to medium weight fabrics B-16 B-17 For light or medium weight fabrics For light or medium weight fabrics For heavier weight fabrics For jeans or trousers B-18 For jeans or stretch fabric with a coarse weave For stretch fabric B-19 NOTE: Before sewing a buttonhole on your project, prac-...
Buttonhole sewing Buttonhole sewing Select the buttonhole stitch. Adjust the stitch width ➌ and the stitch length to the desired width and density. Position the fabric under the presser foot so that the centerline’s mark is aligning with the center of the buttonhole foot.
Page 49
W B uttonhole sewing Buttonhole sewing Buttonholes are sewn from the front of the presser ➏ B-16 foot to the back, as shown. Cut the center of the buttonhole with the seam ripper ➐ being careful not to cut any stitches on either side. Use a pin as a stopper at the bar tack so you do not cut too much.
Buttonhole sewing Making corded buttonholes When sewing corded buttonholes, hook a heavy thread or cord under the buttonhole foot. Attach the buttonhole foot and hook the gimp thread ➊ onto the back of the presser foot. Bring the two gimp thread ends to the front of the foot and insert them into the grooves, then temporarily tie them there.
Patterns Bar Tack Stitch Bar tack stitch B-27 Select pattern to get the bar tack stitch. Change the ➊ presser foot to the buttonhole foot. Pull the button holder to the rear. Set the 2 button ➋ guide plate on the buttonhole foot to the desired length.
Eyelet Stitch Patterns Eyelet stitch Patterns B-23 Select pattern 22 to get the eyelet stitch. Attach ➊ presser foot A. Press the ”−“ or ”+“ stitch width adjustment to button ➋ select the eyelet size. Size of eyelet: A Large: 7.0 mm (1/4 inch). B Medium: 6.0 mm (15/64 inch).
NOTE Make no gap here Patterns Darning Stitch Patterns Darning stitch B-24 B-25 Select pattern 23 or 24 to get the darning stitch. ➊ Change the presser foot to the buttonhole foot. Baste the upper fabric and the reinforcement fabric ➋...
Page 54
Darning Stitch Darning stitch Position the fabric so that the needle is 2mm (1/16 ➎ inch) in front of the area to be darned, and then lower the presser foot. NOTE: When lowering the presser foot, do not push in the front of the presser foot, otherwise the darning will not be sewn with the correct size.
5 cm 5 cm 5 cm 5 cm Zipper Insertion Zipper insertion ATTENTION: Zipper foot should be used with machine set for straight stitch only. Care should be given when choosing needle position (choose 3.5, the center position) as the needle could hit the presser foot and break when sewing with an altered needle position or with any other pattern.
Zipper Insertion Inserting a lapped zipper Baste the zipper opening on the garment. ➊ Fold back to the left seam allowance. Turn under the ➋ right seam allowance to form 3 mm (1/8 inch) fold. Attach the zipper foot. Attach the right side of the ➌...
Narrow Hemming Narrow hemming * The Rolled hem foot is an optional accessory. Fold the edge of the fabric over about 3 mm ➊ (1/8 inch), then fold it over again 3 mm (1/8 inch) for about 5 cm (2 inches) along the edge of the fabric. ➊...
Cording Cording B-15 Sew over one, two or three strands of cord to embellish fabrics. Pearl cotton, embroidery floss or fine wool yarn can be used for cording. * The Cording foot is an optional accessory. Single cording Mark the design on the fabric. Insert the cord in ➊...
W S atin Stitch Sewing Satin stitch sewing Use the satin stitch foot for satin stitching and sew- B-28 B-30 B-31 B-32 B-33 B-34 B-35 B-36 ing decorative stitches. This foot has a groove on the B-28 B-30 B-31 B-32 B-33 B-34 B-35 B-36 underside which allows dense stitching to pass freely underneath.
Edge / Quilting Guide Edge / Quilting Guide * The Quilting foot is an optional accessory. Insert the edge/quilting guide in the presser foot ➊ holder as illustrated and set the space as you desire. Sew the first row and move over the fabric to sew ➋...
W G athering Gathering * The Gathering foot is an optional accessory. Remove the presser foot holder and attach the gath- ➊ ering foot. Place fabric to be gathered under the presser foot. Sew a row of stitching. The stitches will automatically cause the fabric to gather.
Smocking Smocking B-14 B-15 Use the all purpose foot to sew straight lines 1 cm ➊ (3/8“) apart, across the area. It may be helpful to reduce the needle thread tension slightly, so that the bobbin thread may be drawn later to gather the fabric.
Free Motion Sewing Free motion sewing (Embroidery, Darning, monograms) * The Darning foot is an optional accessory. Move the drop feed lever to (b) to lower the feed ➊ ▲▲ dogs. Remove the presser foot holder, and attach the ➋ darning foot to the presser foot holder bar.
Page 64
Free Motion Sewing Free motion sewing (Embroidery, Darning, monogramming) ➊ Embroidery Stitch along the outline of the design by moving the embroidery hoop. Select zigzag stitch pattern and adjust the stitch width as desired. When sewing, make sure to maintain a constant speed. Fill in the design working from the outline towards the inside.
W W alking Foot Walking foot * The Walking foot is an optional accessory. NOTE: Always try to sew first without the walking foot accessory which should be used only when necessary. It is easier to guide the fabric and you have a better view of the seam when using the standard, regular foot on your machine.
Fagoting Fagoting B-13 Separate the folded edges of the fabric pieces with a ➊ gap of 4 mm (1/8 inch) and baste them onto a piece of thin paper or water-soluble stabilizer sheet. Align the center of the presser foot with the center of ➋...
Decorative Topstitching Decorative Topstitching B-15 B-41 Place the two fabrics, right sides together, and sew ➊ using a straight stitch. Open the seam allowance and press it flat. ➋ Working on the right side of the fabric, place the cen- ➌...
Scallop Stitch Scallop hem B-66 Fold the fabric, right sides together. Sew along the ➊ folded edge, as illustrated. Cut the fabric along the seam leaving an allowance of ➋ 3 mm (1/8 inch) for seaming. Notch the allowance. Turn fabric over and push out the curved seam to the ➌...
Mirror Image Mirror image NOTES: – The Direct Patterns 8 / 9 /10 and Patterns 15-26 can- not be mirror imaged. Patterns – Mirror imaged patterns can also be combined with ➊ other patterns. Select the pattern. ➊ Pressing the mirror button, ➋...
Twin Needle Using the twin needle * The twin needle is an optional accessory. Insert the twin needle. ➊ NOTE: When using twin needles, use the all purpose foot regardless of what kind of sewing method will be carried out. Use only twin needle assemblies with max.
W M emory Memory Combined patterns can be stored for later use. Since stored patterns are not lost after the sewing machine is turned off, they can be recalled at any time. This is ➊ convenient for patterns such as names, which may be used frequently.
Page 72
W M emory Combining patterns or letters Press the button to leave the memory mode and ➎ return to the Direct mode. ATTENTION: The selected pattern will be cleared from the memory module after turning off the machine if you do not press the button again when you have com- pleted your selection.
Page 73
W M emory Recalling and sewing the memorized pattern Press the button to enter the memory mode. The ➊ machine will be positioned at the first programmed stitch. Press foot controller. The machine will start to sew ➋ from first entered pattern. On the LCD screen, sewing ➊...
Warning Functions Warning beeping sound – When operating correctly: 1 beep – When the memory is full 30 units of pattern: 3-short beeps – When operating incorrectly: 3-short beeps – When the sewing machine is in trouble and can’t sew: ➊...
W B uzzer Sound Sound on Press on the stitch width button and turn on the power switch, the sound on mode will be set. Sound off Press on the stitch width button and turn on the power switch, the sound off mode will be set.
Maintenance Maintenance Cleaning the hook Lint and bits of thread may accumulate in the hook and will interfere with the smooth operation of the machine. Check regularly and clean the stitching mechanism when necessary. ATTENTION: Disconnect the machine from the wall outlet before carrying out any mainte- nance.
W T rouble Shooting Guide Problem Cause Correction Page Problem Cause Correction Page Upper 1. The machine is not threaded 1. Rethread the machine. Needle 1. The needle is damaged. 1. Insert a new needle. thread correctly. breaks 2. The needle is not correctly 2.