Sony HKCU-HB10 Maintenance Manual page 80

Page Menu / Menu Image
C06 INCOM/PGM
<INCOM/PGM>
FP-INCOM
(MIC ON) (PRIVATE)
PGM-MODE : OFF
PGM-SEL : MIX
PGM1 : 0
PGM2 : 0
SIDE TONE: 0
INCOM-CH : 2CH
C07 PROMPT/TRUNK
<PROMPT/TRUNK> ?C07 TOP
PROMPTER: 1CH
TRUNK SETTINGS
CH : 2CH
IF : 232C
TRANSMIT: AUTO
CABLE : CAMERA CABLE
AUX REMOTE: DISABLE
C08 VIDEO SETUP
<VIDEO SETUP>
SETUP : OFF
SD BLK CLP: OFF
Q FILTER : WD
G/Y SYNC : OFF
VCS RELAY : ON
C09 VIDEO ADJUST
(When using EN-159 board)
<VIDEO ADJUST 1> C09 TOP
VBS LEVEL :
CHROMA:
PIX LEVEL :
CHROMA:
WFM LEVEL :
CHROMA:
[|||||]: The settings in the box are default values.
4-14 (E)
Item
FP-INCOM
C06 TOP
PGM-MODE
PGM-SEL
PGM1
PGM2
SIDE TONE
INCOM-CH
PROMPTER
TRUNK SETTING
CH
IF
TRANSMIT
CABLE
AUX REMOTE
SETUP
?C08 TOP
SD BLK CLP
Q FILTER
G/Y SYNC
VCS RELAY
VBS
LEVEL
CHROMA
0
0
PIX
0
LEVEL
0
0
0 CHROMA
WFM
LEVEL
CHROMA
Setting Description
(MIC ON/OFF/PGM ON) Displays the FRONT INCOM MIC SW settings.
(PROD/ENG/PRIVATE) Displays the FRONT INCOM line settings.
SEP/MIX/ OFF Sets the PGM-MODE output.
Selects the PGM-MODE.
MIX/ PGM1 /PGM2
_99 to 0 to +99
Sets PGM1 level.
_99 to 0 to +99
Sets PGM2 level.
_99 to 0 to +99
Sets SIDE TONE level.
Selects INCOME CHANNEL.
1CH/ 2CH
1CH /2CH
Sets line number for Prompter (Fixed to 1
channel for HDCU1500.)
Sets line for TRUNK.
1CH/ 2CH Sets the channel number used.
232C /422A Sets the communication line mode.
n
The AUX REMOTE function is enabled
only for version A of the AVP board (board
suffi x -41 and later)
AUTO/ HD-SDI / Sets the mode of transmission with the
camera.
High Bitrate
AUTO:
n
Change the setting from HD-SDI:
HD-SDI to AUTO after the
High Bitrate: Transmission mode is always
software is upgraded to
V3.00 and later.
CAMERA CABLE /COAX Sets the type of cable to be connected
between the camera and the HDCU.
CAMERA CABLE: Optical fi ber cable.
COAX:
Sets whether to enable or disable the AUX
ENABLE/ DISABLE
REMOTE connector to be added on the
rear panel of the HDCU1000.
OFF /ON
Turns ON/OFF the SETUP.
Clips the Y signal of lower than 0% to be
OFF /ON
supplied from the SD SDI output
connector, at 0%
WD /NA Sets width of Q-Filter. (Only when the EN
board is attached)
OFF/ ON Turns ON/OFF Gch-SYNC for the R/G/B
component signal.
(Only when the EN board is attached)
OFF/ ON Sets PIX/WFM terminal output mode. (Only
when the EN board is attached)
Adjusts the VBS output video level.
_99 to 0 to +99
_99 to 0 to +99
Adjusts the PIX output video level.
_99 to 0 to +99
_99 to 0 to +99
Adjusts the WFM output video level.
_99 to 0 to +99
_99 to 0 to +99
Judges High Bitrate and
HD-SDI automatically.
Transmission mode is always
HD-SDI.
High Bitrate.
Coaxial cable
HKCU-HB10