Opus Atlas 300 mono User Manual page 5

9
10
8
8
8/9
7
15
B
14
A
If the documents are not thick enough, it is necessary to use filling strips called, O.filling Important!
If the documents are not thick enough for choising channel, it is necessary to use filling strips called,
Sticky, to make documents thick enough to bind, which is available from OPUS .
O.Filling Sticky, to make documents thick enough to bind, which is available from OPUS . See our web-
See our website www.opus.pl/en
site www.opus.pl/en
2. Make sure the COVER guide is correctly inserted into the binding slot (3) (see PREPARATION TO
WORK and diagram above).
2. Make sure the binding bars are correctly inserted into the binding slot (3).
3. Lift up the bind and de-binding handle (1) to the open position, vertical.
3. Adjust the extend back support (13) and set it to suit the binding bar being used.
4. Move the clamp lever (2) completely to the left, till it is locked in position.
For the thick binding bar (9) set the extend back support fully to the back, for the thin
5. Put the channel into the binding slot (3) between the COVER guide bar (8) and binding jaw.
binding bar (8) fully forward.
Insure that the channel is tight against the side stop right (10) and the front of the chan-
4. Lift the handle (1) to the vertical position.
nel is against the COVER guide bar (8) see diagram above. When using shorter channels than
5. Move the clamp lever (2) completely to the left, till it is locked in position.
A4 fit and use the adjustable side stop (11). Ensure the shorter channel is in the centre of the
6. Put the channel into the binding slot (3) between the binding bar (8) or (9) and binding
jaw by using the ruler on the COVER guide in the slot and tighten the side stop (11).
jaw. Insure that the channel is tight against the side stop right (11) and the front of the
The adjustable side stop should be removed before de-binding.
chan nel is against the binding bar (8) or (9) see diagram above. When using shorter
6. Push the handle (1) down, the clamping lever (2) will move to the channel automatically to
channels than A4 fit and use the adjustable side stop (12). Ensure the shorter channel is in
hold it firmly. Now pull the handle back to the open position.
the centre of the jaw by using the ruler on the binding bar in the slot and tighten the side
7. Take the documents and insure they are even, put them between the covers, check the pages
stop (12).The adjustable side stop should be removed before de-binding.
are centred in relation to the edges of covers.
7. Push the handle (1) down, the clamping lever (2) will move to the channel automatically
8. Take the documents and covers and push carefully into the channel between the protru-
to hold it firmly. Now pull the handle back to the open position.
sions, which is in the binding slot. NOTE that some O.CHANNELS and O.SIMPLE CHANNELS do
8. Take the documents and insure they are even, put them between the covers, check the
not have protrusions. Make sure the back cover is facing you.
pages are centred in relation to the edges of covers.
9. Push the handle (1) down. The jaw will close the channel on to the document clamping
9. Take the documents and covers and push carefully into the channel between the
them firmly. If you do not feel any pressure, pull the handle back and push it once more till
protru s ions, which is in the binding slot. NOTE that some channels do not have
you fill the pressure.
protrusions. Make sure the back cover is facing you.
10. Now pull the handle (1) to the open position, vertical. Move the clamp lever (2) to the left
10. Push the handle (1) down. The jaw will close the channel on to the document clamping
completely till it locks, then remove the bound documents.
them firmly. If you do not feel any pressure, pull the handle back and push it once more
11. If the documents are not clamped together firmly enough, repeat the process 9 and 10 aga-
till you fill the pressure.
in. If it is still not bound enough, use a smaller channel or O.Filling sticky.
Important!
Be sure the back cover faces you.
Back cover
Atlas 190 • User guide
OPUS Atlas 300 mono • User guide
8 - COVER guide
9 - Fixed guide
8 - Binding bar thin
9 - Binding bar thick
A - Channel 1.5 - 20 mm
10 - Cover guide
B - Binding jaw
14 - Channel 1.5-32 mm
15 - Binding jaw
1
2
11. Now pull the handle (1) to the open
position, vertical. Move the clamp lever (2)
to the left completely till it locks, then
remove the bound documents.
12. If the documents are not clamped together
firmly enough, repeat the process 10 and
11 aga i n. If it is still not bound enough, use
a smaller channel or O.Filling sticky.
5
5
EN
EN
1
back cover