Opus Atlas 300 mono User Manual page 10

NOTE! In case of customized matrixes only O.Frame Matrix GP can be used.
4. Put the frame on the heaters face of the Image Press
Note! The heating time of a matrix depends on its size and can
vary from few to tens of minutes. Therefore it is necessary to
NOTE! The heating time of a matrix depends on its size and can vary from few to tens of
conduct a test to check if the matrix is hot enough.
minutes. Therefore it is necessary to conduct a test to check if the matrix is hot enough.
13 HOT PRINT STAMPING ON COVERS
HOT STAMPING ON COVERS
12
1. Put the front cover into the binding slot. Make sure it is
1. Put the front cover into the binding slot.
placed upside down.
Make sure it is placed upside down.
2. Put the piece of hot stamping foil between the cover
2. Put the piece of hot stamping foil between
and the frame.
the cover and the frame.
NOTE! Use the magnet to fix the foil to the Image Press and
Note! Use the magnet to fix the foil to the
remove word this avoids the foil slipping down.
Image Press and avoid slipping down of the
foil.
3. Push the handle (1) down - holding the cover at the same time until the clamp lever moves to
the right and the Image Press with matrix will move to the cover. Now pull the handle (1) back
3. Move the adjusting lever (2) to the right
and push it once more to complete the process. If you do not feel any pressure, pull the
(until you feel the resistance) holding the cover at the same time.
handle back and push it once more till you fill the pressure.
4. Press the handle (1) down holding the cover at the same time.
4. N ow pull the handle (1) to the open position, vertical. Move the clamp lever (2) to the left
5. Lift the handle (1), move the lever (2) to the left.
completely till it locks, then remove the bound documents.
6. Take the cover out of the binding slot, take o the foil.
5. T ake the cover out of the binding slot, remove the foil gently.
Note! If hot stamping is uneven you can adjust the heater ver-
NOTE!
tical or horizontal. To do this, use Allen key - size 2.
If the hot print stamping is not level you can adjust the heater vertical
or horizontal. To do this, use Allen key - size 2.
a) Horizontal heater inclination adjustment - if the pressure is big-
ger on the right side, the screw need to be rotated to the left
a) Horizontal heater inclination adjustment - if the pressure is bigger
(see the picture). However, If the pressure is bigger on the left
on the right side, the screw need to be rotated to the left (see the
side, the screw need to be rotated to the right
picture). However, If the pressure is bigger on the left side, the screw
b) Vertical heater inclination adjustment - if the pressure is big-
ger in the upper side, the screw need to be rotated in to the need to be rotated to the right.
b) Vertical heater inclination adjustment - if the pressure is bigger in the right side (see the picture). However, if the pressure is bigger
on the bottom side, the screw need to be rotated to the left
upper side, the screw need to be rotated in to the right side (see the
picture). However, if the pressure is bigger on the bottom side, the screw
need to be rotated to the left.
10
Note! Before sticking the matrix, make sure that the inscrip-
NOTE! Detailed instructions for gluing the matrix are with O•Matrix
tion/logo on the matrix is parallel to the bottom edge of the
Base GP plate.
plate (O.Matrix Base GP)
NOTE! Before sticking the matrix, make sure that the inscription
3. Put the base with a matrix on it into O.Frame Matrix GP. / logo on the matrix is parallel to the bottom edge of the plate
(O.Matrix Base GP)
Note! In case of customized matrixes only O.Frame Matrix GP
3. Put the base with a matrix on it into O.Frame Matrix GP.
can be used.
4. Put the frame on the back wall of the Image Press
Note! The heating time of a matrix depends on its size and can
vary from few to tens of minutes. Therefore it is necessary to
conduct a test to check if the matrix is hot enough.
HOT STAMPING ON COVERS
12
1. Put the front cover into the binding slot.
Make sure it is placed upside down.
2. Put the piece of hot stamping foil between
the cover and the frame.
Note! Use the magnet to fix the foil to the
Image Press and avoid slipping down of the
foil.
3. Move the adjusting lever (2) to the right
(until you feel the resistance) holding the cover at the same time.
4. Press the handle (1) down holding the cover at the same time.
5. Lift the handle (1), move the lever (2) to the left.
6. Take the cover out of the binding slot, take o the foil.
Note! If hot stamping is uneven you can adjust the heater ver-
tical or horizontal. To do this, use Allen key - size 2.
a) Horizontal heater inclination adjustment - if the pressure is big-
ger on the right side, the screw need to be rotated to the left
(see the picture). However, If the pressure is bigger on the left
side, the screw need to be rotated to the right
b) Vertical heater inclination adjustment - if the pressure is big-
ger in the upper side, the screw need to be rotated in to the
right side (see the picture). However, if the pressure is bigger
on the bottom side, the screw need to be rotated to the left
10
Note! Before sticking the matrix, make sure that the inscrip-
tion/logo on the matrix is parallel to the bottom edge of the
plate (O.Matrix Base GP)
3. Put the base with a matrix on it into O.Frame Matrix GP.
Note! In case of customized matrixes only O.Frame Matrix GP
can be used.
4. Put the frame on the back wall of the Image Press
front
cover
magnet
magnet
10
1
front
cover
magnet
front
foil
cover
2
foil
foil
1
2
2