Related Manuals for Emerson MicroMotion HPC010
Summary of Contents for Emerson MicroMotion HPC010
- Page 1 Installation Manual MMI- 20032352, Rev AD March 2020 ™ Micro Motion High Pressure Coriolis Flow Meters...
- Page 2 Micro Motion employees. Micro Motion will not accept your returned equipment if you fail to follow Micro Motion procedures. Return procedures and forms are available on our web support site at www.emerson.com, or by phoning the Micro Motion Customer Service department.
-
Page 3: Table Of Contents
Installation Manual Contents MMI- 20032352 March 2020 Contents Chapter 1 Before you begin......................5 1.1 About this document........................5 1.2 Hazard messages..........................5 1.3 Related documentation........................5 Chapter 2 Planning........................7 2.1 Installation checklist......................... 7 2.2 Best practices........................... 8 2.3 HPC010 vibration limits — vibration broadband random..............8 2.4 HPC015 vibration limits........................ - Page 4 Contents Installation Manual March 2020 MMI- 20032352 Micro Motion HPC...
-
Page 5: Before You Begin
Related documentation You can find all product documentation on the product documentation DVD shipped with the product or at www.emerson.com. See any of the following documents for more information: • The hazardous area approvals documentation shipped with the sensor or available at www.emerson.com/flowmeasurement. - Page 6 Before you begin Installation Manual March 2020 MMI- 20032352 • Micro Motion 9-Wire Flowmeter Cable Preparation and Installation Guide • The transmitter installation and configuration and use guides Micro Motion HPC...
-
Page 7: Chapter 2 Planning
Installation Manual Planning MMI- 20032352 March 2020 Planning Installation checklist □ If you plan to mount the meter in a hazardous area: WARNING Make sure that the hazardous area specified on the approval tag is suitable for the environment in which the meter will be installed. □... -
Page 8: Best Practices
Planning Installation Manual March 2020 MMI- 20032352 □ Orient the sensor so that personnel and equipment will not be exposed to escaping pressurized discharge from the rupture disk. The sensor has a rupture disk to evacuate the case in the unlikely event of a loss of primary containment. □... -
Page 9: Temperature Limits
• Temperature limits may be further restricted by hazardous area approvals. Refer to the hazardous area approvals documentation shipped with the sensor or available from www.emerson.com/flowmeasurement. Installation Manual... - Page 10 Planning Installation Manual March 2020 MMI- 20032352 Micro Motion HPC...
-
Page 11: Chapter 3 Mounting
Installation Manual Mounting MMI- 20032352 March 2020 Mounting Mount the HPC010 sensor Use your common practices to minimize torque and bending load on process connections. To reduce the risk of condensation problems, do not orient transmitters or sensor junction boxes with their conduit openings pointing upward. NOTICE Lifting the sensor by the electronics or rupture disk can damage the device. -
Page 12: Mount The Hpc015 Sensor
Mounting Installation Manual March 2020 MMI- 20032352 Mount the HPC015 sensor Procedure 1. Mount the sensor. 2. Optional: Use a bracket to mount the HPC015 sensor to a wall. Micro Motion HPC... -
Page 13: Mount The Enhanced Core Processor
Installation Manual Mounting MMI- 20032352 March 2020 Mount the enhanced core processor Procedure 1. If desired, reorient the core processor housing on the bracket. a) Loosen each of the four cap screws. b) Rotate the bracket so that the core processor is oriented as desired. c) Tighten the cap screws, torquing to 2.2 ft lbf (3 N m) to 3 ft lbf (4 N m). -
Page 14: Mount The I.s. Barrier
Mounting Installation Manual March 2020 MMI- 20032352 Figure 3-3: Wall mount Mount the I.S. barrier ™ ™ Use this procedure if you are mounting an MVD Direct Connect I.S. barrier. Procedure 1. Snap the barrier onto a 1.38 in (35 mm) DIN rail. You can mount it in either direction. -
Page 15: Attach Extended Electronics
Installation Manual Mounting MMI- 20032352 March 2020 Attach extended electronics If your installation has a sensor with extended electronics, you will need to install the extender onto the sensor case. Extended core processors are matched at the factory to specific sensors. Keep each core processor together with the sensor with which it was shipped. - Page 16 Mounting Installation Manual March 2020 MMI- 20032352 Micro Motion HPC...
-
Page 17: Transmitter Power And I/O Wiring
Installation Manual Transmitter power and I/O wiring MMI- 20032352 March 2020 Transmitter power and I/O wiring Options for wiring The wiring procedure you follow depends on which electronics option you have. Table 4-1: Wiring procedures by electronics option Electronics option Wiring procedure Integral transmitter The transmitter is already connected to the sensor. - Page 18 Transmitter power and I/O wiring Installation Manual March 2020 MMI- 20032352 User-supplied cable must meet the following requirements: • Twisted pair construction. • Applicable hazardous area requirements, if the core processor is installed in a hazardous area. • Wire gauge appropriate for the cable length between the core processor and the transmitter, or the host.
- Page 19 Installation Manual Transmitter power and I/O wiring MMI- 20032352 March 2020 4.2.4 Prepare a cable with user-supplied cable glands Procedure 1. Remove the core processor cover using a flat-blade screw driver. 2. Pass the wires through the gland. 3. Terminate the shield and drain wires inside the gland. 4.
- Page 20 Transmitter power and I/O wiring Installation Manual March 2020 MMI- 20032352 7. For foil (shielded cable) only: Note For braided (armored cable) skip this step and contine to the next step. Option Description a. Slide the shielded heat shrink over the drain wires. Ensure that the gland wires are completely covered.
- Page 21 Installation Manual Transmitter power and I/O wiring MMI- 20032352 March 2020 10. Insert the wires through the gland body and tighten the gland nut onto the gland body. A. Shield folded back B. Gland body 4.2.6 Connect the wires to the core processor terminals After the 4-wire cable has been prepared and shielded (if required), connect the individual wires of the 4-wire cable to the terminals on the core processor.
-
Page 22: Connect 9-Wire Cable
Transmitter power and I/O wiring Installation Manual March 2020 MMI- 20032352 Connect 9-wire cable 4.3.1 Connect the 9-wire cable Procedure 1. Prepare and install the cable according to the instructions in the Micro Motion 9-Wire Flowmeter Cable Preparation and Installation Guide. 2. - Page 23 Installation Manual Transmitter power and I/O wiring MMI- 20032352 March 2020 Function Core processor terminals Barrier I.S. terminals VDC + VDC – c) Connect the RS-485 wires to the non-I.S. RS-485 terminals at the barrier (terminals 13 and 14). These wires will be used in the next step to connect the barrier to the remote host.
- Page 24 Transmitter power and I/O wiring Installation Manual March 2020 MMI- 20032352 Figure 4-2: Barrier terminals A. I.S. terminals for connection to enhanced core processor B. Non I.S. terminals for connection to remote host and power supply Micro Motion HPC...
-
Page 25: Chapter 5 Grounding
Installation Manual Grounding MMI- 20032352 March 2020 Grounding The meter must be grounded according to the standards that are applicable at the site. The customer is responsible for knowing and complying with all applicable standards. Prerequisites Use the following guides for grounding practices: •... - Page 26 Grounding Installation Manual March 2020 MMI- 20032352 Micro Motion HPC...
-
Page 27: Purge The Sensor Case
Installation Manual Purge the sensor case MMI- 20032352 March 2020 Purge the sensor case Prerequisites Make sure the following are available before beginning the purge procedure: ™ • Teflon tape • Argon or nitrogen gas sufficient to purge the sensor case Whenever a purge plug is removed from the sensor case, you must purge the case again. - Page 28 Purge the sensor case Installation Manual March 2020 MMI- 20032352 • If the purge gas is lighter than air (such as nitrogen), locate the inlet higher than the outlet, so that the purge gas will displace air from top to bottom. 5.
-
Page 29: Chapter 7 Pressure Relief
Installation Manual Pressure relief MMI- 20032352 March 2020 Pressure relief HPC sensors are available with a rupture disk installed on the case. Rupture disks vent process fluid from the sensor case in the unlikely event of a flow tube breach. Some users connect a pipeline to the rupture disk to help contain escaping process fluid. - Page 30 Pressure relief Installation Manual March 2020 MMI- 20032352 WARNING • Orient the sensor so that personnel and equipment will not be exposed to any discharge along the pressure relief path. • Stay clear of the rupture disk pressure relief area. High-pressure fluid escaping from the sensor can cause severe injury or death.
- Page 31 Installation Manual MMI- 20032352 March 2020 Installation Manual...
- Page 32 © 2020 Micro Motion, Inc. All rights reserved. The Emerson logo is a trademark and service mark of Emerson Electric Co. Micro Motion, ELITE, ProLink, MVD and MVD Direct Connect marks are marks of one of the Emerson Automation Solutions family of companies. All other marks are property of their respective owners.