Related Manuals for IDTECK NEO RF245
Summary of Contents for IDTECK NEO RF245
- Page 1 User Manual NEO RF245 LONG RANGE READER December. 2016 Copyright IDTECK Co., Ltd.
-
Page 2: Table Of Contents
8. OUTPUT FORMAT AND TIMING ····························································································11 9. WIRE CONNECTION TO CONTROLLER ·················································································12 10. OPERATION ······························································································································13 11. FCC REGISTRATION INFORMATION ····················································································17 12. WARRANTY POLICY AND LIMITATION OF LIABILITY ·····················································18 13. HOW TO MAKE RMA REQUEST (AFTER SALES SERVICE) ··············································19 December. 2016 Copyright IDTECK Co., Ltd. -
Page 3: Safety Information
- When water or liquid gets into the device, turn off the power first. Caution - Cleaning - When cleaning, do not spray water directly onto parts of the product. - Clean only with dry cloth. - Do not use chemicals or cleaning products. December. 2016 Copyright IDTECK Co., Ltd. -
Page 4: Introduction
2. Introduction NEO RF245 is outdoor long range reader of 2.45GHz. If used with IDA245(N)/IDA245(N)H2 Active Tag, reading range can be selected up to 15 M depending on the installation environment. NEO RF245 can be used for hands-free access control, parking management, circulation management and factory automation. -
Page 5: Specification
10% to 90% relative humidity non-condensing Color / Material Ivory / Polycarbonate / Anodized Aluminum Dimension(W x H x T) 7.1” x 7.1” x 1.6” (180mm x 180mm x 40mm) Weight 1.15Kg(excluding Mounting Bracket) Certificate FCC, CE, KC, RoHS December. 2016 Copyright IDTECK Co., Ltd. -
Page 6: Identifying Supplied Parts
5. Identifying Supplied Parts Unpack and check the contents. If any of these parts are missing, contact your distributor. NEO RF245 Quick Installation Guide Mounting Bolts Mounting Bracket ON/OFF Switch for Reading range setting December. 2016 Copyright IDTECK Co., Ltd. -
Page 7: Installation Of The Product
User Manual 6. Installation of the Product December. 2016 Copyright IDTECK Co., Ltd. - Page 8 User Manual Extra Purchase Reader hood, bargate, loop coil and speed bump are extra purchase. (IDTECK doesn’t offer these contents) Reading Angle of NEO RF245 The reading angle of RF245 is approximately 90 degree at the front side of the reader. However the reader has about 10% of the maximum reading distance at the rear side of the reader.
- Page 9 F.2 Multiple Gates with OTR & HOLD Control 1. NEO RF245 is applicable in a various way as it shows in F.1 and F.2. However, because of the characteristic of a long range reader, we recommend to have enough space between each of them when installing multiple RF245 (ex: F.1 : 3m, F.2 : 5m at least).
-
Page 10: Cable Color
The maximum current drain rate is 1 Amps. HOLD input is used to force NEO RF245 to read a tag when loop sensor detects any approaching vehicle. When a vehicle is detected, NC contact should be used, and the input should also be disconnected from GND completely. -
Page 11: Output Format And Timing
Baud Rate: 9600bps, Parity: None, Data bit: 8, Stop bit: 1 LRC: Exclusive OR (XOR) from Start(0x02h) to End(0x03h) Card ID Start(0x02h) End(0x03h) LRC(XOR) total 11 bytes (8 ASCII char.) 8-3 Bargate output Timing Low active pulse: 1 sec duration Transistor (open collector) output December. 2016 Copyright IDTECK Co., Ltd. -
Page 12: Wire Connection To Controller
Connect both yellow (OTR, one time reading) and white (WIEGAND-1) cable to the ON/OFF switch (the switch must be ON when setting up reading range). Turn ON the switch when setting up reading range. Make sure to turn it OFF after a desired range is setup. December. 2016 Copyright IDTECK Co., Ltd. -
Page 13: Operation
When the HOLD Control Input (Blue wire) is grounded, it will prevent the reader from reading the tag. This can be used for vehicle detectors such as Loop Coil Sensor. Hold Input with OTR function will only detect on tag ID. Please refer to the following figure. December. 2016 Copyright IDTECK Co., Ltd. - Page 14 User Manual - Reading range setting method ☞ NEO RF245 is suitable for any installation environment that the users can freely set the reading range at the desired distance. 10-6 Power off NEO RF245. 10-7 Connect yellow (OTR, one time reading) and white (Wiegand_D1) cables together.
- Page 15 (Bee Bee Beep) will be generated. Now the distance of that 10 time of scanning will be programmed as a new reading distance. When finished, the reading range setup will be finalized and green LED will turn off. December. 2016 Copyright IDTECK Co., Ltd.
- Page 16 ※ Note: 1. Reading range can have a margin of error that depends on installation circumstances. 2. The default reading range of NEO RF245 is set to maximum. (Reading Range is definable according to each site's properties.) December. 2016 Copyright IDTECK Co., Ltd.
-
Page 17: Fcc Registration Information
1. Reorient or relocate the receiving antenna. 2. Increase the separation between the equipment and receiver. 3. Connect the equipment into an outlet on another circuit. 4. Consult the dealer or an experienced radio/TV technician for help. December. 2016 Copyright IDTECK Co., Ltd. -
Page 18: Warranty Policy And Limitation Of Liability
This Warranty doesn’t apply: 1) to any product which has been dismantled without authorization of IDTECK or/and has a damaged or detached QC label on its back side; 2) to any losses, defects, or damages caused by improper testing, operation, installation, maintenance, modification, alteration, or adjustment;... -
Page 19: How To Make Rma Request (After Sales Service)
Please refer to the IDTECK webpage for more details. RMA Code will be issued after the RMA Center reviews the RMA request form. Enclose the product along with the RMA Code and send it to IDTECK RMA Center. (Product without RM A Code is not accepted.) If you have any questions or problems regarding the RMA services, please contact us using the contact information below. - Page 20 The specifications contained in this manual are subject to change without notice at any time. 5F, Ace Techno Tower B/D, 468, Gangseo-ro, Gangseo-Gu, Seoul, 07573, Korea Tel : +82-2-2659-0055 Fax : +82-2-2659-0086 E-mail : webmaster@idteck.com Dec. 2016 Copyright IDTECK Co., Ltd.