Installation Precautions - Nice RMKIT Series Instructions And Warnings For Installation And Use

1
GENERAL WARNINGS: SAFETY - INSTALLATION - USE (original instructions in Italian)
CAUTION Important safety instructions. Observe all the instructions as improper installation may cause serious
damage
CAUTION Important safety instructions. It is important to comply with these instructions to ensure personal safety.
Store these instructions
• Before commencing the installation, check the "Product technical specifications", in particular whether this product is suitable for
automating your guided part. Should it be unsuitable, DO NOT proceed with the installation
• The product cannot be used before it has been commissioned as specified in the "Testing and Commissioning" chapter
CAUTION According to the most recent European legislation, the implementation of an automation system must
comply with the harmonised standards set forth in the Machinery Directive in force, which allow for
declaring the presumed conformity of the automation. On account of this, all operations regarding
connection to the mains electricity, as well as product testing, commissioning and maintenance, must be
performed exclusively by a qualified and skilled technician!
• Before proceeding with the product's installation, check that all materials are in good working order and are suitable for the intended
applications
• The product is not intended for use by persons (including children) with reduced physical, sensory or mental capacities, nor by
anyone lacking sufficient experience or familiarity with the product
• Children must not play with the appliance
• Do not allow children to play with the control devices of the product. Keep the remote controls out of reach of children
CAUTION In order to avoid any danger from inadvertent resetting of the thermal cut-off device, this appliance must not be
powered through an external switching device, such as a timer, or connected to a supply that is regularly powered
or switched off by the circuit
• Provide a disconnection device (not supplied) in the plant's mains power supply, with a contact opening distance that ensures
complete disconnection under Category III overvoltage conditions
• Handle the product with care during installation, taking care to avoid crushing, knocks, falls or contact with liquids of any kind. Keep
the product away from sources of heat and open flames. Failure to observe the above can damage the product and increase the
risk of danger or malfunctions. Should this occur, suspend the installation process immediately and contact the technical Assistance
Service
• The manufacturer declines all liability for damages to property, objects or people resulting from failure to observe the assembly
instructions. In such cases the warranty does not cover material defects
• The weighted sound pressure level of the emission A is lower than 70 dB(A)
• Cleaning and maintenance to be carried out by the user must not be effected by unsupervised children
• Before intervening on the automation for maintenance or cleaning purposes, always disconnect the motor from the mains power
supply
• Check the system periodically, in particular the cables, springs and supports to detect possible imbalances, signs of wear or
damage. Do not use the automation if repairs or adjustments are necessary, because a fault concerning the installation or an
incorrectly balanced automation may lead to injury
• The packaging materials of the product must be disposed of in compliance with local regulations
• The wording on the tubular motors can be covered after assembly
• If the cable is damaged, the appliance must be scrapped. The power cable cannot be replaced
• Be careful when the shutter is moving and keep away from it until it comes to a standstill
• Be careful when activating the manual release device, as a raised shutter may rapidly drop if the springs are weak or broken
• Do not activate the shutter when maintenance activities – such as window cleaning – are being carried out nearby
• Prior to installing the drive motor, remove any unnecessary cables and disable any appliance not required for motor-driven operation
• Install the manoeuvring assembly for manual release at a height below 1.8 m
NOTE: if removable, the manoeuvring assembly must be kept close to the door
• Make sure that the controls are kept at a safe distance from moving parts, while allowing a good view of these.
Unless a selector is used, the controls should be installed at least 1.5 m from the ground and must not be accessible
• The fixed control devices must be installed in a visible position
• For drive motors that allow for accessing unprotected moving parts once they have been installed, such parts must be installed 2.5
m above the floor or other surface form which they can be accessed
• Prior to installing the drive motor, remove any unnecessary cables and disable any appliance not required for motorised operation
• Install the manoeuvring assembly for manual release at a height below 1.8 m
NOTE: if removable, the manoeuvring assembly must be kept close to the door
• Make sure that the controls are kept at a safe distance from moving parts, while allowing a good view of these.
Unless a selector is used, the controls should be installed at least 1.5 m from the ground and must not be accessible
• The fixed control devices must be installed in a visible position
5 – English

INSTALLATION PRECAUTIONS