Intended Use - Orbea ORDU OMX Technical Manual

10 | ORBEA
TELESCOPIC SEAT POSTS:
· Inspection of its operation before each ride.
· Inspection and full maintenance every 125 hours or once
authorized dealer.
PIVOT POINTS ON FULL SUSPENSION FRAMES:
· Inspection of its operation before each ride.
· Disassembly of the frame and the manual inspection of
all the bearings every 125 hours of use or once a year
pending on the conditions in which the bicycle is ridden.
More demanding use of the bicycle or use in adverse
weather conditions or in mud requires the disassembly
and inspection of the frame once every 75 hours of use
ing does not turn smoothly or has excessive play, it must
be replaced immediately.
GEAR CABLES AND HOUSING:
· Inspection of its operation before each ride.
· Replacement of gear cables every 6 months to 1 year
depending on the conditions in which the bicycle is used.
BRAKES:
· Inspection of the operation and wear of the brake pads or
shoes before each ride.
· Check the wear on disc brakes and the cables or hydrau-
lic lines every 6 months to 1 year depending on the con-
ditions in which the bicycle is used. Flush the hydraulic
lines once a year.
Some of these checks and maintenance
needs go beyond the mechanical knowledge
of most bicycle users. If you are not quali-
always visit an Orbea dealer for maintenance
on your bicycle and its components. The
failure to perform proper maintenance can
result in malfunctions and accidents with se-
rious consequences.
Maintenance performed incorrectly can dam-
age the components, which are not covered
by the warranty conditions.
TECHNICAL MANUAL
R E PLAC E ME N T PA RTS
Always use original Orbea replacement parts or those from
the component manufacturer in question.
The use of non-original replacement parts may
cause damage that results in malfunctions
and accidents with serious consequences.
- The installation of some of the replacement
parts in this technical manual are beyond
the mechanical knowledge of most bicycle
replacement parts, always visit an Orbea
- dealer for maintenance on your bicycle and
its components. The failure to properly install
replacement parts can result in malfunctions,
accidents and serious injuries.
The installation of non-original replacement
parts can damage your bicycle and is not
covered by the warranty conditions.
AFTER A CRASH OR AN IMPACT
Falling off your bike is part of cycling. If you have an acci-
dent on your Orbea bicycle, be sure that you're okay and
seek medical care, if necessary. If you are uninjured, you
should check the condition of your bicycle before conti-
nuing to ride.
INSPECT THE FRAME AND THE BICYCLE COMPO-
NENTS TO SEE IF THEY HAVE BEEN DAMAGED IN
ANY WAY
If you detect any problem, do not continue to ride the
bicycle.
POINTS TO CHECK
Inspect the frame and the fork to identify whether either of
these components have been broken or bent. If you detect
any damage or cracks, you must stop using the bicycle im-
mediately. On carbon frames, look for cracks or soft spots
in the carbon. If you detect any of these symptoms, you
must stop using the bicycle immediately.
BLUE PAPER ORDU · OMX 2021
The materials used on carbon frames and
forks are rigid and strong, but if overloaded
bend, and they will break. A strong enough
impact to this material could cause damage
cause the materials to fail in the future. In the
case of any doubt about the consequences of
a fall or accident, contact your Orbea dealer
for a correct diagnosis of the materials.
Check the drivetrain and the wheels to make sure that the
components operate correctly. If you discover any damage
to the components, stop using the bicycle immediately.
Even if you do not observe any damage, pay close atten-
tion to the sound of your bicycle when you ride it again.
Damage and other problems can cause unusual noises.
If you notice any unusual noise, stop using your bicycle
immediately and contact your Orbea dealer for a correct
diagnosis of the problem.
TAKE YOUR ORBEA BICYCLE TO AN AUTHORIZED
DEALER FOR A PROFESSIONAL INSPECTION
Some of the consequences of a fall or accident can only be
detected by completely disassembling the bicycle to check
for the presence of damage or other signs of deterioration.
A collision or impact can cause serious da-
mage to your bicycle and its components,
causing them to malfunction or wear out
prematurely. Malfunctions can occur sud-
denly and without notice, causing you to lose
control of your bicycle and suffer serious in-
juries, or even death.
ORBEA | 11
0 4 WA R NI NG S
O F US E
M AXIM UM TYR E WIDTH
tyres that can be mounted on the frame. Always follow
these guidelines when installing tyres on your bicycle.
However, the real measurements of the tyre circumfer-
ence and width may change from one manufacturer to
another. When installing a tyre other than that originally
mounted on your Orbea bicycle, check that there is at
least 3 mm between the top and the sides of the tyre and
any part of the frame.
Damage to the frame or components due
to the use of a tyre that does not comply with
these measurements is not covered by the
warranty conditions.
MINIMUM SEATPOST
A ND F RONT PO ST INSERT ION
the minimum insertion depth of the seatpost
or the frame on road bicycles with exclusi-
ve Orbea seatposts.On Ordu, also observe
the instructions for the minimum front post
insertion. The failure to follow these instruc-
tions can cause stresses on the materials
beyond the conditions for which they were
designed and cause damage not covered by
the warranty conditions, as well as accidents
that can result in serious injuries.
INT ENDED USE
The intended use of all models is
ASTM Condition 1, for use on a
regular paved surface where the
tyres are intended to mantain
ground contact.
For information about all ASTM
categories, consult the General
User Manual.
EN