Summary of Contents for Backyard Discovery BEACH FRONT
Page 1
MANUFACTURED BY: Wooden Swing Set Backyard Discovery 3305 Airport Drive Pittsburg, KS 66762 Owner's Manual & Assembly Instructions Model # 1605022B 800-856-4445 average 2 person assembly time assembly time may vary based on skill level For the most up to date assembly manual, to register your set, or to order replacement parts please visit www.backyarddiscovery.com...
Page 2
INSTALLATION SERVICES AVAILABLE! Need a helping hand? Let our team of professionals handle the installation for you! *Installation services are only available to U.S. customers. With Go Configure, we bring you 18 years of experience right to your doorstep. We service a wide array of indoor and outdoor recreation products that most consumers don’t have the time or ability to deliver &...
Page 3
Please Read This Before Starting Assembly MISSING A PART? CALL US BEFORE GOING BACK TO THE STORE Th e store where you made your purchase does not stock parts for this item. If you have assembly questions or you are missing or have damaged parts, please call you can also visit www.backyarddiscovery.com or e-mail customerservice@backyarddiscovery.com...
Page 4
Botanical, Adventure Playsets, and Leisure Time Products. Backyard Discovery warrants that this product is free from defect in materials and workmanship for a period of one (1) year from the original date of purchase. Th is one (1) year warranty covers all parts including wood, hardware, and accessories. All wood carries a fi ve (5) year pro-rated warranty against rot and decay. Refer to the schedule below for charges associated with replacement of parts under this Limited Warranty.
Page 5
Operating Instructions and Safety Warnings WARNING: BURN HAZARD • Pay special attention to plastic and metal surfaces as they may be hot enough to cause burns. • Always check the temperature of the product before NOTE: letting your children play on it. •...
Page 6
Please Read This Before Starting Assembly Positioning Your Playcenter Suggested Playground Surfacing • Th e playcenter is designed to be installed on a level • Do not install home playground equipment over surface by an adult with an adult helper. Place concrete, asphalt, packed earth, grass, carpet, or any in a fl at area of your yard to minimize ground other hard surface.
Page 7
Please Read This Before Starting Assembly APPENDIX A The following information is from the United States X3.1.3.2 Do not install loose-fi ll surfacing over hard surfaces such as concrete or asphalt. Consumer Product Safety Commission’s Information X3.1.4 Poured-In-Place Surfaces or Pre-Manufactured Sheet for playground surfacing material;...
Page 8
Check all moving parts including swing seats, third party person or service to assemble this product. ropes, cables, and chains for wear, rust, or other Backyard Discovery assumes no responsibility or deterioration. Replace as needed. liability for any charge incurred by the Customer for any assembly services’...
Page 9
About Our Wood Backyard Discovery uses 100% Cedar (C. Lanceolata) wood. Although we take great care in selecting the best quality lumber available, wood is still a product of nature and susceptible to weathering which can change the appearance of your set.
Page 10
Assembly Tips Protrusion Hazard Incorrect Correct If you see exposed threads and your bolt protrudes beyond the T-Nut you may have over tightened the bolt or used incorrect hardware. If you’ve overtightened, remove the bolt and add washers to eliminate the protrusion.
Page 11
Assembly Tips ASSEMBLY TIP: Keep an eye out for these boxes which will contain helpful pictures and information making the assembly process as quick and painless as possible. Sorting Wood When removing the wood from the boxes we recommend arranging them by part number before you begin assembly.
Page 13
Owner's Manual Place the set on level ground, not less than 6'-7" [2 m] from any structure or obstruction such as a fence, garage, house, overhanging branches, laundry lines, or electrical wires. While assembling unit, take time before and after each phase to make sure fort is level. If fort is not level, assembly will be difficult and improper assembly may result.
Page 20
Owner's Manual A100069 L BRACKET A4M00646 QUICK LINK L BRACKET A4M01048 BLUE 32x51 2.5x38x55x55 A100153 L BRACKET 66x66x127 BLUE TRIANGLE "A" REVISION A100314 A100309 PLATE BLUE 100 SWING BEAM SWING BEAM A4M00512 5 HOLE A4M00511 EXT BRACKET EXT. BRACKET BLUE - RIGHT BLUE - LEFT A4M00524 CHAIN BLUE 51.25"...
Page 21
Owner's Manual A6P00124 AWNING A6P00123 TARP A6P00131 SLIDE BED 8' LIME A100161 SLIDE RAIL 8' BLUE RIGHT A100162 SLIDE RAIL 8' BLUE LEFT A6P00133 A100164 BYD ID TAG (LARGE) AGES 3-10 SWING SEAT BLUE 22" A6P00128 A6P00129 A6P00040 LIME HC ROCK #2 CRANBERRY HC ROCK #1 BLUE HC ROCK #2 HAND GRIP LIME...
Page 36
SLIDE ASSEMBLY SLIDE BRACE - W100544 5/8"x3 3/8"x17 1/4" (16x86x438) (x1) A6P00131 SLIDE BED 8' LIME (x1) H100074 T-NUT H100115 BOLT WH (x3) 5/16 (x3) 5/16x1/2 PLACE 'M77' SLIDE BRACE BOARD 1/2" FROM THE BOTTOM EDGE OF THE SLIDE BED. USING THE BOARD AS A TEMPLATE, MARK WHERE THE PILOT HOLES WILL BE DRILLED.
Page 37
SLIDE ASSEMBLY A100162 SLIDE RAIL 8' BLUE LEFT (x1) CENTER SLIDE BRACE - W100545 5/8"x3 3/8"x17 1/4" (16x86x438) (x2) A100161 SLIDE RAIL 8' BLUE RIGHT (x1) H100090 SCREW PFH (x24) 8x2 1/2" USING A 1/8" DRILL BIT, DRILL PILOT HOLES IN EACH INDENTATION ALONG EACH SIDE RAIL. THERE SHOULD BE 8 INDENTIONS ON EACH RAIL.
Page 57
FORT ASSEMBLY H100145 LAG SCREW WH H100142 BOLT WH 1/4x1 1/2 1/4x1-1/4 HAND GRIP LIME A6P00127 H100072 T-NUT H100138 WASHER H100108 WASHER PLASTIC LOCK EXT LOCK INT 6x15 8x15...
Page 58
FORT ASSEMBLY PICKET - W4L06944 H100088 SCREW PFH 5/8"x1 3/8"x18 1/4" (16x34x465) (14) 8x1 1/8 CENTER O2 BOARDS IN OPENING, APPROXIMATELY 1 7/8" - 46mm DOWN FROM M8 BOARD. APPROXIMATELY 3 1/8" - 79mm SPACING BETWEEN PICKETS.
Page 59
FORT ASSEMBLY PICKET - W4L06944 H100088 SCREW PFH 5/8"x1 3/8"x18 1/4" (16x34x465) (18) 8x1 1/8 CENTER O2 BOARDS IN OPENING, APPROXIMATELY 1 7/8" - 46mm DOWN FROM M10 BOARD. 2 7/8" - 72mm SPACING BETWEEN PICKETS.
Page 60
FORT ASSEMBLY PICKET - W4L06944 H100088 SCREW PFH 5/8"x1 3/8"x18 1/4" (16x34x465) (14) 8x1 1/8 CENTER O2 BOARDS IN OPENING, APPROXIMATELY 1 7/8" - 46mm DOWN FROM M8 BOARD. APPROXIMATELY 3 1/8" - 79mm SPACING BETWEEN PICKETS.
Page 61
FORT ASSEMBLY HORIZONTAL TARP SUPPORT - W4L13838 H100013 BOLT WH 1"x3 3/8"x56 1/8" (24x86x1425) 5/16x2 1/4 H100008 BOLT WH 5/16x1 L BRACKET A4M01048 2.5x38x55x55 HORIZONTAL TARP SUPPORT - W4L13839 H100115 BOLT WH H100005 NUT BARREL 1"x3 3/8"x48 3/4" (24x86x1237) 5/16x1/2 5/16x7/8 H100030 WASHER...
Need help?
Do you have a question about the BEACH FRONT and is the answer not in the manual?
Questions and answers