Connecting Video Components - Yamaha DSP-AZ1 Owner's Manual

Connecting video components

Before you connect any components, disconnect the power supply to all the components you plan to connect including this unit and deter-
mine which jacks are for the left and right channels and for input and output. After you finish all connections, check them again to make sure
they are correct.
I About the video jacks
There are three types of video jacks.
DIGITAL
GND R
1
LD
RF
LD
(AC–3)
2
1
CD
CD
3
2
COAXIAL DVD
TUNER
IN
4
3
CABLE
IN
(PLAY)
CD–R
5
4
CD–R
OUT
(REC)
OPTICAL
6
OUT
3
MD/
TAPE IN
(PLAY)
MD/TAPE
7
4
CD
OUT
(REC)
8
CD–R MAIN
9
DVD SURROUND
OPTICAL
0
IN
D–TV SUB
/LD WOOFER
q 6CH INPUT
SAT
w
VCR 3
/DVR
DIGITAL
1
Composite VIDEO jack
Video signals input through the VIDEO jacks are the conventional
composite video signals.
2
S VIDEO jack
Video signals input through the S VIDEO jacks are separated into
luminance (Y) and color (C) video signals. The S-video signals
achieve high quality color reproduction. When you are using the S
VIDEO jacks, check the details in the owner's manual that came
with the component being connected.
3
COMPONENT VIDEO jacks
Video signals input through the COMPONENT VIDEO jacks are
separated into luminance (Y) and color difference (P
video signals. The jacks are also separated into three for each signal.
The labels of the component video jacks may be different depend-
ing on the component (e.g. Y, C
Component video signals provide the best quality in picture
reproduction. When you are using the COMPONENT VIDEO
jacks, check the details in the owner's manual that came with the
component being connected.
1 2 3
AUDIO AUDIO VIDEO COMPONENT VIDEO
PHONO L R L VIDEO S VIDEO Y P /C
B B
DVD A
D–TV
B
/LD
CABLE C
SAT
PREOUT/MAIN IN
IN
VCR 1 R
CONTROL
OUT
IN
IN
VCR 2 REMOTE 1
OUT
OUT
REMOTE 2
MONO
IN
IN
VCR 3
REAR CTR
/DVR
RS–
232C
OUT
CENTER
1
VIDEO
R L
MONITOR
OUT
CTRL
2
OUT
10mA
R
+12V MAX.
ZONE 2 OUT
/C , P /C
B B R
, C / Y, P , P / Y, B-Y, R-Y/ etc.).
B R B R
SPEAKERS
P /C FRONT
R R R L
DVD
D–TV
/LD
SAT
REAR
R
MONITOR
OUT
FRONT
IN
L
(SURROUND)
FRONT
OUT
REAR
(SURROUND)
SUB
WOOFER
SPLIT
CENTER REAR CENTER
CENTER
IN
R B L R A L
MAIN
CENTER
OUT
MAIN
IN
MAIN
OUT
L CAUTION
SEE INSTRUCTION MANUAL FOR CORRECT SETTING.
Cautions
• Use a commercially available S-video cable when connecting to
the S VIDEO jacks, and commercially available video cables
when connecting to the COMPONENT VIDEO jacks.
• Each type of video jack works independently. Signals input
through the composite video, S-video, and component jacks are
output through the corresponding composite video, S-video, and
component jacks respectively.
• If your video monitor is connected only to the COMPONENT
VIDEO jacks of this unit, the OSD is not shown.
Note
• You can designate the input for the COMPONENT VIDEO A, B
)
R
and C jacks according to your component by using "8 I/O
ASSIGNMENT" on the SET MENU (see page 58 for details).
CONNECTIONS
MAINS
IMPEDANCE SELECTOR
SET BEFORE POWER ON
FRONT : 6ΩMIN. /SPEAKER FRONT : 8ΩMIN. /SPEAKER
REAR : 4ΩMIN. /SPEAKER REAR : 8ΩMIN. /SPEAKER
REAR CENTER : 4ΩMIN. /SPEAKER REAR CENTER : 8ΩMIN. /SPEAKER
CENTER : 4ΩMIN. /SPEAKER CENTER : 8ΩMIN. /SPEAKER
MAIN A OR B : 4ΩMIN. /SPEAKER MAIN A OR B : 8ΩMIN. /SPEAKER
L
A + B : 8ΩMIN. /SPEAKER A + B : 16ΩMIN. /SPEAKER
AC OUTLETS
SWITCHED
VOLTAGE SELECTOR
E-
21