Impedance Selector Switch - Yamaha DSP-AZ1 Owner's Manual

Yamaha av amplifier owner's manual
Hide thumbs Also See for DSP-AZ1:
Table of Contents

Advertisement

CONNECTIONS
Subwoofer system
Right
PREOUT/MAIN IN
CONTROL
IN
REMOTE 1
OUT
REMOTE 2
IN
RS–
232C
CTRL
OUT
10mA
+12V
MAX.
Subwoofer system
Right rear speaker
SPEAKERS
FRONT
R
L
REAR
R
L
(SURROUND)
CENTER
REAR CENTER
WARNING
Do not change the IMPEDANCE SELECTOR switch setting
while the power to this unit is on, otherwise this unit may be
damaged.
IF THIS UNIT FAILS TO TURN ON WHEN THE STANDBY/
ON SWITCH IS PRESSED:
The IMPEDANCE SELECTOR switch may not be set to either
end. If so, set the switch to either end when this unit is in the
standby mode.
IMPEDANCE SELECTOR
SET BEFORE POWER ON
FRONT
: 6ΩMIN. /SPEAKER
REAR
: 4ΩMIN. /SPEAKER
REAR CENTER
: 4ΩMIN. /SPEAKER
CENTER
: 4ΩMIN. /SPEAKER
MAIN A OR B
: 4ΩMIN. /SPEAKER
A + B
: 8ΩMIN. /SPEAKER
E-
30
Subwoofer system
Left
FRONT
IN
R
L
FRONT
OUT
REAR
(SURROUND)
SUB
WOOFER
SPLIT
MONO
CENTER
IN
REAR CTR
CENTER
OUT
MAIN
IN
MAIN
OUT
R
L
Left rear speaker
Subwoofer system
MAINS
FRONT
: 8ΩMIN. /SPEAKER
REAR
: 8ΩMIN. /SPEAKER
REAR CENTER
: 8ΩMIN. /SPEAKER
CENTER
: 8ΩMIN. /SPEAKER
MAIN A OR B
: 8ΩMIN. /SPEAKER
A + B
: 16ΩMIN. /SPEAKER
AC OUTLETS
SWITCHED
I Connecting a front subwoofer
Connect the signal input jack on your subwoofer to the PREOUT/
MAIN IN SUBWOOFER MONO jack.
By connecting two subwoofers to the SUBWOOFER SPLIT jacks,
this unit can reproduce subtle directional changes in the low
frequency sounds.
When you use two subwoofers, connect both of them to the
SUBWOOFER SPLIT jacks using pin plugs.
I Connecting a rear subwoofer
By using both front and rear subwoofers, the CINEMA-DSP sound
field programs can produce realistic movie effects with powerful,
dynamic sound. To take advantage of this dynamic sound, be sure to
set the "1C REAR L/R SP" item in the SET MENU to "LARGE"
(see page 36).
Caution
• Adjust the speaker volume for the subwoofer with the controls on
the subwoofers, not on this unit.
I Impedance selector switch
Select the position whose requirements your speaker system meets.
(Upper position)
Front effect: The impedance of each speaker must be 6Ω or
higher.
Rear:
The impedance of each speaker must be 4Ω or
higher.
Rear Center: The impedance of the speaker must be 4Ω or higher.
Center:
The impedance of the speaker must be 4Ω or higher.
Main:
If you use one pair of main speakers, the impedance
of each speaker must be 4Ω or higher. If you use
two pairs of main speakers, the impedance of each
speaker must be 8Ω or higher.
(Lower position)
Front effect: The impedance of each speaker must be 8Ω or
higher.
Rear:
The impedance of each speaker must be 8Ω or
higher.
Rear Center: The impedance of the speaker must be 8Ω or higher.
Center:
The impedance of the speaker must be 8Ω or higher.
Main:
If you use one pair of main speakers, the impedance
of each speaker must be 8Ω or higher. If you use
two pairs of main speakers, the impedance of each
speaker must be 16Ω or higher.

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents