Danfoss VLT AQUA Drive FC 202 Operating Instructions Manual page 69

Specifications
Type designation
1)
High/normal overload
Typical shaft output at 550 V [kW]
Typical shaft output at 550 V [hp]
Typical shaft output at 690 V [kW]
Typical shaft output at 690 V [hp]
IP20/Chassis
IP21/Type 1
IP55/Type 12/Type 3R
Output current
Continuous (3x525–550 V) [A]
Intermittent (60 s overload) (3x525–550 V) [A]
Continuous (3x551–690 V) [A]
Intermittent (60 s overload) (3x551–690 V) [A]
Continuous kVA at 550 V [kVA]
Continuous kVA at 690 V [kVA]
Maximum input current
Continuous at 550 V [A]
Intermittent (60 s overload) at 550 V [A]
Continuous at 690 V [A]
Intermittent (60 s overload) at 690 V [A]
Additional specifications
Maximum cable cross-section for mains and
2
motor [mm ] ([AWG])
Maximum cable cross-section for brake and
2
load sharing [mm ] ([AWG])
2)
Maximum cable cross-section for mains
2
disconnect [mm ] ([AWG])
3)
Estimated power loss
at rated maximum load [W] 4)
Efficiency 5)
Table 8.17 B4, C2, C3 Enclosure, Mains Supply 3x525–690 V AC IP20/IP21/IP55 – Chassis/NEMA1/NEMA 12, P30K–P75K
For fuse ratings see chapter 8.8 Fuses and Circuit Breakers.
1) High overload=150% or 160% torque for a duration of 60 s. Normal overload=110% torque for a duration of 60 s.
2) The 3 values for the maximum cable cross-section are for single core, flexible wire and flexible wire with sleeve, respectively.
3) Applies for dimensioning of frequency converter cooling. If the switching frequency is higher than the default setting, the power losses may
increase. LCP and typical control card power consumptions are included. For power loss data according to EN 50598–2, refer to
www.danfoss.com/vltenergyefficiency.
4) Efficiency measured at nominal current. For energy efficiency class see chapter 8.4.1 Ambient Conditions. For part load losses see
www.danfoss.com/vltenergyefficiency.
5) Measured using 5 m screened motor cables at rated load and rated frequency.
6) Enclosure sizes A2+A3 can be converted to IP21 using a conversion kit. See also Mechanical mounting and IP21/Type 1 Enclosure kit in the
design guide.
7) Enclosure sizes B3+B4 and C3+C4 can be converted to IP21 using a conversion kit. See also Mechanical mounting and IP21/Type 1 Enclosure kit
in the design guide.
8) Enclosure sizes for N75K, N90K are D3h for IP20/Chassis, and D5h for IP54/Type 12.
9) Two wires are required.
10) Variant not available in IP21.
11) Type 3R is not available in A4 enclosures.
MG20MC22
Operating Instructions
P37K P45K
HO NO HO NO
22 30 30 37
30 40 40 50
30 37 37 45
40 50 50 60
B4 C3
C2 C2
36.0 43.0 43.0 54.0
54.0 47.3 64.5 59.4
34.0 41.0 41.0 52.0
51.0 45.1 61.5 57.2
34.3 41.0 41.0 51.4
40.6 49.0 49.0 62.1
36.0 49.0 49.0 59.0
54.0 53.9 72.0 64.9
36.0 48.0 48.0 58.0
54.0 52.8 72.0 63.8
95 (3/0)
600 740 740 900
0.98 0.98
Danfoss A/S © 01/2015 All rights reserved.
8)
P55K P75K/N75K
HO NO HO NO
37 45 45 55
50 60 60 75
45 55 55 75
60 75 75 100
C3 D3h
C2 C2
54.0 65.0 65.0 87.0
81.0 71.5 97.5 95.7
52.0 62.0 62.0 83.0
78.0 68.2 93.0 91.3
51.4 61.9 61.9 82.9
62.1 74.1 74.1 99.2
59.0 71.0 71.0 87.0
87.0 78.1 105.0 95.7
58.0 70.0 70.0 86.0
87.0 77.0 105 94.6
150 (300 MCM)
95 (3/0)
185, 150, 120
(350 MCM, 300
MCM, 4/0)
900 1100 1100 1500
0.98 0.98
8)
P90K/N90K
HO NO
55 75
75 100
75 90
199 125
D3h
C2
87.0 105
130.5 115.5
83.0 100
124.5 110
82.9 100
99.2 119.5
87.0 99.0
8 8
129 108.9
– –
– –
–
1500 1800
0.98
67