Danfoss VLT AutomationDrive FC 303 Instruction Manual page 104

Index
Pre-start.................................................................................................. 3-1
Programming
Programming... 1-2, 2-10, 3-6, 4-2, 4-4, 5-3, 5-4, 5-9, 8-4, 3-3,
Example............................................................................................. 5-1
Protection And Features.............................................................. 10-15
Pulse/Encoder Inputs.................................................................... 10-13
Q
Quick
Menu.................................................................................. 5-1, 5-3, 4-2
Set-up................................................................................................. 3-4
R
Ramp-down Time............................................................................... 3-6
Ramp-up Time...................................................................................... 3-5
RCD........................................................................................................... 2-6
Reference...................................................................... 0-1, 7-2, 7-3, 4-2
Relay Outputs.......................................................................... 2-8, 10-14
Remote
Commands........................................................................................ 1-3
Programming................................................................................... 5-9
Reference........................................................................................... 7-2
Reset........................................... 4-1, 4-4, 7-3, 8-1, 8-5, 8-7, 8-10, 4-3
RFI Filter.................................................................................................. 2-7
RMS Current.......................................................................................... 1-4
Run
Command......................................................................................... 3-6
Permissive......................................................................................... 7-2
S
Safety Inspection................................................................................. 3-1
Serial Communication...... 1-3, 2-8, 2-9, 4-3, 4-4, 7-1, 7-2, 7-3, 8-
Setpoint.................................................................................................. 7-3
Set-up.............................................................................................. 3-6, 4-2
Shielded
Cable.................................................................................. 2-1, 2-5, 3-2
Control Cables................................................................................. 2-9
Wire..................................................................................................... 2-5
Specifications.................................................................. 1-2, 2-15, 10-1
Speed Reference...................................................... 2-10, 3-6, 5-2, 7-1
Start Up................................................................................................... 5-1
Start-up.......................................................................... 1-2, 4-4, 3-1, 3-2
Status
Messages........................................................................................... 7-1
Mode................................................................................................... 7-1
Stop Command.................................................................................... 7-2
Supply Voltage................................................... 2-7, 2-8, 3-1, 8-5, 8-7
VLT ® AutomationDrive Instruction
Manual
4-1, 4-3, 5-1
6, 8-1, 2-14
®
MG.33.AI.22 - VLT is a registered Danfoss trademark
Surroundings................................................................................... 10-15
Switching Frequency................................................................ 7-2, 8-5
Symbols.................................................................................................. 0-1
System
Feedback........................................................................................... 1-3
Monitoring........................................................................................ 8-1
Start-up.............................................................................................. 3-6
T
Technical Data................................................................................. 10-11
Temperature Limits............................................................................ 3-2
Terminal
53...................................................................................... 5-1, 2-10, 5-1
54....................................................................................................... 2-10
Programming................................................................................ 2-10
Programming Examples............................................................... 5-2
Thermistor
Thermistor........................................................................ 2-7, 8-5, 6-4
Control Wiring................................................................................. 2-7
Tightening Of Terminals.............................................................. 10-25
Torque
Characteristics............................................................................ 10-11
Limit..................................................................................................... 3-5
Transient Protection.......................................................................... 1-4
Trip
Trip....................................................................................................... 8-1
Function............................................................................................. 2-5
Lock..................................................................................................... 8-1
Troubleshooting................................................................. 1-2, 8-4, 9-1
V
Voltage Level................................................................................... 10-11
W
Warning
And Alarm Definitions.................................................................. 8-2
And Alarm Displays........................................................................ 8-1
And Alarm Types............................................................................. 8-1
Warnings................................................................................................ 8-1
Wire
Wire..................................................................................................... 2-6
Sizes............................................................................................ 2-5, 2-6
12-3