Table of Contents
Advertisement
Quick Links
MOS-MT wireless ceiling mount IoT sensor
Overview
This guide covers the MOS-MT IoT Ceiling Sensor.
1. MOS-MT-xA Motion, photo, temperature and audio sensor with small
motion short range lens (1000 sq. ft.)
2. MOS-MT-xB Motion, photo, temperature and audio sensor with large
motion large range lens (1900 sq. ft.)
Where x is the frequency of the unit: U=902 MHz or Y=868 MHz.
The package includes the occupancy sensor, lens mask sticker, mounting
plate with integrated magnets for T-Bar ceiling, wire straps and installation
guide. A programming guide with detailed information on implementation is
available for download on www.echoflexsolutions.com.
Sensor Description
The MOS-MT IoT ceiling sensor is a self-powered wireless sensor offering
occupant detection, light level, temperature and sound level monitoring for
the collection of and sharing of data for Internet of Things. Facility operations
use the IoT sensor data via gateways or interfaces to track occupancy levels
and environment mapping for building-use optimization. Areas not being
used can be placed into set-back mode to conserve energy. The detector is
optimized for ceiling heights of 8 - 10 feet (2.4 - 3 meters).
These sensors are intended for indoor use only.
i
Note:
Installation Guide
The MOS is a solar powered device that absorbs solar energy
storing it for use during low light periods. Before assigning
the MOS device to a receiver/controller, the device should be
exposed to a good light source for a minimum of 5 minutes
or install the start assist battery.
MOS-MT
Advertisement
Table of Contents
Related Manuals for ETC echoflex MOS-MT Series
Summary of Contents for ETC echoflex MOS-MT Series
- Page 1 MOS-MT MOS-MT wireless ceiling mount IoT sensor Installation Guide Overview This guide covers the MOS-MT IoT Ceiling Sensor. 1. MOS-MT-xA Motion, photo, temperature and audio sensor with small motion short range lens (1000 sq. ft.) 2. MOS-MT-xB Motion, photo, temperature and audio sensor with large motion large range lens (1900 sq.
-
Page 2: Sensor Operation
Sensor Operation The MOS-MT IoT sensor monitors occupancy, light level, temperature and sound level in interior spaces. The sensor is powered by solar energy from natural or artificial light sources. Powered by six solar cells, the sensor can operate without battery up to 5 days. The sensor will operate even with a brief exposure to light, however for best results the sensor should be mounted in a location with exposure for 2.5 hours of natural or artificial light (minimum of 500 lux or 46 foot-candles) on a daily basis. -
Page 3: Mounting The Sensor
(2.4m) 2.4m 2.4m 7.3m 4.3m 0.9m 0.9m 0.9m 4.3m 7.3m (24ft) (14ft) (8ft) (3ft) (3ft) (3ft) (8ft) (14ft) (24ft) Large Range Lens (B) 1900 sq.ft @ 9 ft. (2.4m) 10ft (3.0m) 12ft (3.7m) 12.2m 9.1m 6.1m 3.0m 3.0m 6.1m 9.1m 12.2m (40ft) (30ft) -
Page 4: Installation Instructions
Installation Instructions Choose a mounting method. 1. The axillary mounting plate allows mounting with the integrated magnets to a steel T-bar ceiling frame or other metallic surface by placing the sensor on the metal rail. 2. With screws and anchors (not provided) to a wall-board ceiling. i. -
Page 5: Test Operating Modes
this guide. Also, a GP teach-in process is required before its data messages can be properly interpreted. See the programing guide (URL on page 8) for more information Test Operating Modes The following tests can be selected when in test mode: •... - Page 6 The red LED will blink every time a motion sensor trigger is detected. The test times out in 100 seconds. If a faster exit from walk test mode is required, press and hold the teach button for 10 seconds. PIR Audio / EEP configuration mode Mode The PIR Audio /EEP configuration mode has a sub menu which allows: •...
- Page 7 blinks, hold the teach button for 6 seconds to select occupancy duration select. A press and release of the button will allow you to scroll through the settings of a repeated blink pattern as shown in the table below. The default duration is 15 minutes.
-
Page 8: Agency Listings
4. A blink will resume. The red LED blinking indicates the motion detection LED is active (default). The green LED blinking indicates the LED is inactive. Tapping the teach button will toggle between these two states. 5. Save and exit by press and holding the teach button for 5 seconds. Energy Code Compliance California Energy Commission Title 24 The MOS-MT sensor is built in an ISO9001 certified facility and is RoHS compliant...