Dell PowerEdge 700 Installation And Troubleshooting Manual page 29

Memory double word logic
failure at address, read
value expecting value
Memory odd/even logic
failure at start address to
end address
Memory write/read failure at
address, read value
expecting value
Faulty application program.
Memory allocation error
Memory module installation guidelines have not
been properly followed.
Memory bank population
error!
Faulty or improperly installed memory modules.
Memory parity interrupt at
address
The spacebar was pressed during POST to
terminate the memory test.
Memory tests terminated by
keystroke
Faulty or missing CD/diskette-drive subsystem,
hard drive, or hard-drive subsystem.
No boot device available
No operating system on hard drive.
No boot sector on hard- disk
drive
Faulty system board.
No timer tick interrupt
Faulty diskette, CD/diskette-drive subsystem, or
hard-drive subsystem.
Non-system disk or disk
error
No operating system on diskette.
Not a boot diskette
Loose cable(s) to expansion card(s); faulty or
improperly installed expansion card.
PCI BIOS failed to install
Error encountered while initializing PCI devices.
Plug & Play Configuration
error
Faulty or improperly installed hard drive.
Primary drive n
configuration error
Primary drive n failure
The specified drive on the primary channel of the
integrated hard drive controller is set to Auto in
the System Setup program, but no drive is
Primary drive n not found
attached; improperly installed hard drive; loose
interface or power cable.
Faulty diskette, CD/diskette-drive subsystem, or
hard-drive subsystem.
Read fault
Requested sector not found
Improperly connected diskette drive, tape drive,
hard drive, or power cable.
Reset failed
Restart the application program.
See "Memory Module Installation
Options."
See "Troubleshooting System Memory" in
System."
Information only.
Use a bootable diskette, CD, or hard drive. If the problem persists, see
"Troubleshooting a Diskette Drive,"
RW/DVD Drive," "Troubleshooting SATA Hard
"Troubleshooting SCSI Hard Drives" in
Check the hard-drive configuration settings in the System Setup
program (see "Using the System Setup Program" in your User's Guide).
See "Getting Help."
See "Troubleshooting a Diskette Drive,"
or CD-RW/DVD Drive," "Troubleshooting SATA Hard
"Troubleshooting SCSI Hard Drives" in
If the problem persists, see "Getting
Use a bootable diskette.
Ensure that all appropriate cable(s) are securely connected to the
expansion card(s). If the problem persists, see
Expansion Cards" in "Troubleshooting Your
Install the NVRAM_CLR jumper and reboot the system (see
for jumper location). If the problem persists, see
Expansion Cards" in "Troubleshooting Your
Ensure that the CD drive cables are properly connected. See
"Troubleshooting a CD, DVD, or CD-RW/DVD
Your System."
Run the System Setup program to correct the drive settings (see
"Using the System Setup Program" in your User's Guide). If the problem
persists, see "Troubleshooting SATA Hard
SCSI Hard Drives" in "Troubleshooting Your
See "Troubleshooting a Diskette Drive,"
or CD-RW/DVD Drive," "Troubleshooting SATA Hard
"Troubleshooting SCSI Hard Drives" in
If the problem persists, see "Getting
Ensure that all cables are securely connected. If the problem persists,
see "Getting Help."
Guidelines" in "Installing System
"Troubleshooting Your
"Troubleshooting a CD, DVD, or CD-
Drives," or
"Troubleshooting Your System."
"Troubleshooting a CD, DVD,
Drives," or
"Troubleshooting Your System."
Help."
"Troubleshooting
System."
Figure A-2
"Troubleshooting
System."
Drive" in "Troubleshooting
Drives" or "Troubleshooting
System."
"Troubleshooting a CD, DVD,
Drives," or
"Troubleshooting Your System."
Help."