Jumpers And Connectors - Supermicro X11SPA-TF Quick Reference Manual

P c
ackage ontents
• One (1) Supermicro Motherboard
• Six (6) SATA Cables
• One (1) I/O Shield

Jumpers and Connectors

Jumper
J9701/J9702 Manufacturing Mode
JPAC1 Audio Enable/Disable
JPG1 VGA Enable/Disable
JPL1/JPL2 LAN1/LAN2 Enable/Disable
JPME2 Intel Manufacturing Mode
JWD1 Watch Dog Function Enable
Connector
12V_PUMP_PWR1
AUDIO FP
BATTERY
COM1/COM2
CPU SLOT1/3/5/7 PCI-E 3.0 x16
CPU SLOT2/4/6 PCI-E 3.0 x8 (IN x16) PCI-E x16 Slots (PCI-E x8 link)
FAN1 ~ 6
FAN A ~ D
HD AUDIO
IPMI_LAN
I-SATA0~7
I-SGPIO1/I-SGPIO2
JD1
JF1
JIPMB1
JL1
JOH1-OH
JP4/JP5
JPI2C1
JPUSB1
JPWR1/3/4
JPWR2
JRK1
JSD1/JSD2
JSPDIF_OUT
JSTBY1
JTPM1
LAN1/LAN2
M.2-C01/C02/C03/C04 PCI-E 3.0 x4
UID-SW
USB0/1
USB2/3
USB4/5, USB6/7
USB8/9
USB10
USB11
VGA
• One (1) Quick Reference Guide
• One (1) GPU to CPU Power Cable
Jumpers
Description
Connectors
12V 4-pin Power Connector for CPU Liquid Cooling Pump
Front Panel Audio Header
Onboard Battery
COM1: COM Port (Back Panel), COM2: COM Header
PCI-E x16 Slots (PCI-E x16 link)
*PCI-E SLOT1 will change to PCI-E x8 link when either M.2-C03 or M.2-C04 is populated with an
SSD. PCI-E SLOT1 will be completely disabled when either M.2-C01 or M.2-C02 is populated with
an SSD.
CPU Fan Headers
System Fan Headers
*The initial system fan speed must not be lower than 600 RPM.
Back Panel High Definition Audio
Dedicated IPMI LAN Port
*For IPMI support, X11SPA-TF is via SPS, whereas X11SPA-T is via ME.
Intel Serial ATA (SATA 3.0) Ports 0~7 (6Gb/sec)
Serial General Purpose I/O Headers
Speaker/Power LED Indicator
Front Control Panel Header
4-pin External I2C Header (for an IPMI card)
Chassis Intrusion Header
Overheat LED Indicator
JP4: Enable/Disable USB10/11, JP5: Enable/Disable USB8/9
Power Supply SMBus I2C Header
Enable/Disable USB6/7 WakeUp
+12V 8-pin CPU Power Connectors (Required)
24-pin ATX Main Power Connector (Required)
Intel RAID Key Header
*A VROC hardware key is required to enable an M.2 RAID card.
SATA DOM (Disk-On-Module) Power Connectors
Sony/Philips Digital Interface (S/PDIF) Out Header
Standby Power Header (5V)
Trusted Platform Module (TPM)
RJ45 1GbE/10GbE LAN Ports
PCI-E M.2 Connectors (Small Form Factor Devices and Other Portable
Devices for High Speed NVMe SSDs)
Unit Identifier (UID) Switch
Front Access USB 2.0 Header
Front Access USB 3.1 Gen1 Header
Back Panel USB 3.1 Gen1 Ports
*X11SPA-TF and X11SPA-T do not support S3 or S4.
*Either USB4/5 or USB6/7 will support standby power.
Back Panel USB 3.1 Gen2 Ports
Front Access USB 3.1 Gen2 Header
Front Access USB 3.1 Gen2 Port (Type A)
VGA Port
Default
Pins 1-2 (Normal)
Pins 1-2 (Enabled)
Pins 1-2 (Enabled)
Pins 1-2 (Enabled)
Pins 1-2 (Normal)
Pins 1-2 (RST)
Description