Nice WIDE M Installer's Instructions page 3

Be Safe!
WARNING!! These are the general safety obligations for the installers and users of ET Nice (Pty)
Ltd automation equipment. A copy of this document also appears in the user instructions. Those
instructions must be issued to the responsible end user during the handover and instruction
meeting.
1. Only suitably qualified persons, may install, repair or service the product. Unless expressly indicated in the user instructions, no
user serviceable components can be found inside any ET Nice (Pty) Ltd automation product.
2. It is important for personal safety to study and follow all the instructions carefully. Incorrect installation or misuse may cause
serious personal harm.
3. Keep the instructions in a safe place for future reference.
4. This product was designed and manufactured, strictly for the use indicated in the accompanying documentation. Any other use
not expressly indicated in the documentation, may damage the product and/or be a source of danger. ET Nice (Pty) Ltd cannot
accept responsibility for improper use or incorrect installation of this product.
5. ET Nice (Pty) Ltd cannot accept responsibility if the principles of good workmanship are disregarded by the installer.
6. ET Nice (Pty) Ltd cannot accept responsibility regarding safety and correct operation of the automation, if other manufacturers'
equipment is added to this product.
7. Do not make any modifications or alterations to this product. Do not substitute any component of this product with any other
component not expressly designed into this product.
8. Anything other than expressly provided for in the accompanying instructions is not permitted.
1. All unnecessary ropes, chains and fasteners must be removed and all unnecessary latches or locks must be disabled from locking.
2. The barrier or door must be balanced correctly where it, neither opens nor closes from any position under its own load. When
operated by hand the barrier or door should be free of hindrance and easily moved (In the case of a garage door if the balancing
springs need to be adjusted the adjustment should only be carried out by a qualified and experienced person).
3. The construction of the barrier or door must be sound and automatable. It is the responsibility of the installer to ensure that the
mechanical components of the barrier or door system are sufficient to withstand the necessary forces in cases of overload.
4. It is the responsibility of the installer to ensure the barrier or door is sufficiently trapped within its range of travel by means of
mechanical ends of travel stoppers.
5. Ensure all fixed mounting points, such as the wall above the door in a garage door system or the posts in a swing barrier system,
are sound and strong enough to allow proper fixing of the operator.
6. It is the responsibility of the installer to ensure the installed position selected for this product, falls within the limitations of the
products ingress protection rating.
7. Ensure the area of installation is not subject to explosive hazards. There should be no volatile gasses or fumes as these can present
a serious safety hazard.
8. All ET Nice (Pty) Ltd garage door operators are supplied with a sealed 15A safety plug on lead for use in an electrical code of practice
approved plug point. Do not extend, modify or replace the plug lead unless duly qualified as an electrician. Before installing the
unit, ensure the mains supply is switched off.
9. ET Nice (Pty) Ltd barrier operators are supplied with a terminal connection for the electrical supply beneath the screwed down
cover of the operator. In the case of a model requiring 220Vac supply at the operator, an all pole negatively biased switch, with a
contact opening of greater than 3mm must be installed within 1.5m of the operator. This switch must be clear of all workings of
the system and must be in a position secure from public access. This switch and its connections must be inspected and passed by
a certified electrician prior to using it.
10. It is the responsibility of the installer to ascertain that the designated persons (including children) intended to use the system,
do not suffer reduced physical sensory or mental capabilities, or lack of experience and knowledge, unless they have been given
supervision or instruction concerning the use of the system by a person responsible for their safety.
11. The drive may not be installed on a door incorporating a wicket door, unless the drive is disabled by the release of the wicket door.
(Wicket door :- A pedestrian door within the main barrier or door)
1. Ensure the working area is clear of obstructions and obstacles.
2. Install the safety warning sticker within clear view of where the barrier or door will be operated from. Typically this would be
adjacent to any fixed trigger switches or on the barrier or door itself.
3. The emergency manual release must be installed where it is no higher than 1.8m from the floor level. This would apply to the cord
in a garage installation or the lockable lever in a barrier installation.
4. Any additional fixed door control switches such as wall consoles or keypads, if installed, must be at a height of at least 1.5m, within
clear sight of the barrier or door and away from any moving components of the system.
Prior to installation:
During installation:
3
Continued overleaf.......